3.0 Copper.pdf find it easy and understand

Focus to learn. All in details

1. ME 2207
ENGINEERING METALLURGY
Md Abdullah Al Mohotadi
Lecturer
Department of Mechanical Engineering,
BAUST, Saidpur
Non-FERROUS MATERIALS
COPPER

2. Chapter outcome
Department of Mechanical Engineering, BAUST
At the end of this chapter you should be learn about:
•Properties and uses of following non-ferrous metals
and their alloys
–Copper
–Aluminum
–Nickel
–Tin
–Lead
—Alloys of noble metals
—Bearing materials
—Spring materials
2

3. Non-Ferrous Metals
Department of Mechanical Engineering, BAUST
•Nonferrous metals-Metals that contain little to no iron
•Alloys-Base metals combined with other metals or
chemicals to enhance the base metals properties
•Non-ferrous metals and alloys are important because they
posses important properties such as, corrosion resistance,
high thermal and electrical conductivity, low density, and/or
ease of fabrication
•Al, Cu, Zn, Mg, Ti, Sn, Pb, Ni, Co, W, V
3

4. 4
Classification of non-ferrous materials
a) Density based:
–light metals and alloys ρ < 5000 kg/m
3
(Mg, Al, Ti)
–medium metals and alloys ρ = 5000...10000 kg/m
3
(Sn, Zn, Sb, Cr, Ni, Mn, Fe, Cu)
–heavy metals and alloys ρ >10000 kg/m
3
(Pb, Ag, Au, Ta, W, Mo)
b) Melting temperature based:
–low melting point T
m< T
m
Pb
= 327 °C (Sn, Pb, Bi)
–medium melting point = 327…1539 °C (Al, Mg, Mn, Cu, Ni, Co, Ag, Au)
–refractory T
m> T
m
Fe
= 1539 °C
Element Ti Cr V Nb Mo Ta W
T
m, °C 1660187519002415261029963410
Non-ferrous metals and alloys

5. Copper
Department of Mechanical Engineering, BAUST
5

6. General Properties of Copper
Department of Mechanical Engineering, BAUST
•Moderate strength in the pure state
•Malleable and ductile
•Very good electrical and thermal conductor
•Good corrosion resistance
•Alloys with Zinc to give brass
•Alloys with Tin and others to make bronze
6

7. 7
Copper and copper alloys
Pure Cu Cu-alloys
Brasses Bronzes Cupronickels
Copper and Major Copper Alloys
Department of Mechanical Engineering, BAUST

8. Details Properties of Copper
Department of Mechanical Engineering, BAUST
In a sufficient pure form copper has following properties-
1.Colour: In a clean polished condition it is lustrous yellowish
red
2.Resistance to atm. corrosion: When exposed to the air in
the presence of moisture and carbon dioxide it becomes
coated with a greenish basic carbonate which under normal
atm. conditions acts as a protection against further
corrosion.
3.Density: It has a density of 8.96X10
3
kg/m
3
8

9. Copper corrosion
Department of Mechanical Engineering, BAUST
9

10. Details Properties of Copper
Department of Mechanical Engineering, BAUST
4.Conductivity: Good heat and electricity conductor
Thermal conductivity = 3.95 W/(cm-K)
Electricity conductivity = 50X10
6
ohm
-1
m
-1
at 20
o
C
5.Melting and boiling points: Melting point of 1083
o
Cand
boiling point of 2325
o
C
6.Co-efficient of expansion: It has co-efficient of linear expansion
equal to 16.7 X10
-6
(K
-1
)
7.Specific Heat Capacity: Between 0 and 100
o
C, it is 390 J/kg.K
10

11. Details Properties of Copper
Department of Mechanical Engineering, BAUST
8.Malleability and Ductility: Its percentage elongation in the
annealed form is 50-60%
9.Other Mechanical Properties:
E= 117 Gpa,
U.T.S. = 220 N/mm2
Y.P. = 69 N/mm2
B.H.N. = 47
10.Crystal Structure: It has face centred cubic structure in its pure
form at ordinary temp.
11.Machinabilityand Weldability: It possesses good machinability
and weldabilityas well as castability.
11

12. Details Properties of Copper
Department of Mechanical Engineering, BAUST
12.Hot and Cold Workability: It is easily worked by cold and hot
processes like rolling, forging, extrusion etc.
13.Fracture: The fracture of cast copper is granular but when
forged or rolled it is slightly fibrous.
14.Alloying: It can make alloys with tin, zinc, aluminium and nickel.
15.Resistance to Corrosion by Other Agents:It is practically
unaffected by caustic alkanies, sea and other waters, but is
strongly attacked by nitric acid. Slowly attacked by hydrochloric
and sulphuric acids.
12

13. Copper Production
Department of Mechanical Engineering, BAUST
13

14. Uses of Copper
Department of Mechanical Engineering, BAUST
Copper is widely used industrially mainly due to its high electrical
and thermal conductivity, good resistance to atm. corrosion and
workability
1)As a heat conducting material:
Radiator elements
Domestic boilers
Moulds of casting metals
Refrigerator tubes
Coils
Vessels
Cooking utensils
Kettles, etc.
14

15. Uses of Copper
Department of Mechanical Engineering, BAUST
2.As an electricity conducting material:
Winding of dynamos, motors, transformers and other coil
Bus-bars
Switchgear parts
Cables
Electrodes for welding machines, electric furnaces
Telephone wires
Lighting conductors, etc
3.As a corrosion resistant materials:
Plating or sheeting of wooden ships
4.Copper used for electrotyping and electroplating
5.Used for making coins
15

16. Copper Alloys
Department of Mechanical Engineering, BAUST
Two main alloys
1. Brasses (পেতল)
2. Bronzes (কাাঁসা-a type of bronze)
Brasses: Alloy of Copper and Zinc. May also contain
small percentages of nickel , lead etc.
Bronzes: Alloy of Copper and tin but generally posses
other elements like zinc, nickel, phosphorus,
aluminium etc.
16

17. Copper Alloys
Department of Mechanical Engineering, BAUST
Brasses: Alloy of Copper and Zinc. May also contain
small percentages of nickel , lead etc.
•α Alloys -(0 to 39% of Zn) –single phase –
f.c.c. -cold working alloys
•α+βAlloys –(39 to 46% of Zn) –two phase
(duplex brasses) –hot working alloys
17

18. Copper Alloys
Department of Mechanical Engineering, BAUST
•α Alloys -(0 to 39% of Zn) –single phase –f.c.c. -cold working alloys
•α+βAlloys –(39 to 46% of Zn) –two phase (duplex brasses) –hot working
alloys
18

19. Copper Alloys
Department of Mechanical Engineering, BAUST
•Cartridge brass (70:30 Brass):
•α brass
•Used for cold rolled sheets, wire drawing, deep drawing, pressing and tube
manufacturing
•T.S. : 333.5 MPa
•Elongation: 70%
•Vickers hardness: 65
•Yellow or Muntzmetal (60-40 Brass):
•An α+βBrass
•Suitable for hot working by rolling, extrusion
•Manufacture of casting
•T.S. : 285-480 Mpa
•Elongation: 25-50%
•Vickers hardness: 60-150
Delta Metal
60 –Cu, 37 –Zn, 3 –Fe
•Good tensile strength and
improve mechanical
properties
•Loss of machinability
19

20. Copper Alloys
Department of Mechanical Engineering, BAUST
•Nickel Silvers:
•Can be both α or α+β
•Previously known as German Silver, though there is no silver
•Nickel improves the mechanical properties, specially ductility and
toughness
•T.S. : 518 Mpa(α)
•Copper: 50-65%
•Nickel: 7-30%
•Zinc: 10-25%
20

21. Copper Alloys
Department of Mechanical Engineering, BAUST
Bronzes: Alloy of Copper and tin but generally posses
other elements like zinc, nickel, phosphorus,
aluminium etc.
Typical bronzes are gunmetal, phosphor
bronze, lead-bronze, Al-bronze etc.
21

22. Copper Alloys
Department of Mechanical Engineering, BAUST
•Gunmetals:
•Originally used chiefly for making guns, it has largely been replaced by
steel.
•Alloy of copper, tin and zinc with the zinc in small proportions upto6 %
(max)
•Typical composition
Cu : 88%
Sn: 10%
Zn : 2%
•T.S. : 221 -310 Mpa
•Elongation: 20%
•BHN: 65 -74
•Gunmetal, which casts and machines well and is resistant to corrosion
fromsteamandsalt water,is used to make steam and hydraulic castings,
valves, gears, statues, and various small objects, such as buttons.
22

23. Copper Alloys
Department of Mechanical Engineering, BAUST
•Aluminium bronzes:
•Alloys of copper and aluminiumalong with appreciable quantities of
iron, nickel and manganese but without tin.
•Can be both α or βaluminium bronzes
•α -aluminium bronzes: 4 -7 % Al
•Alloy containing less than 7% aluminium posses valuable cold
working properties. Suitable for components exposed to corrosion
conditions.
•Have very good ductility, upto80% elongation
•Uses: sheet, strip, tubes and wires etc
23

24. Copper Alloys
Department of Mechanical Engineering, BAUST
•Aluminium bronzes:
•β-aluminiumbronzes: 7 -12 % Al
•Alloys containing 7 –12% Al are of duplex structure in which beta
constituents are present in considerable quantities and are much
harder but less ductile
•With a little bit of iron (3%), this alloy can have U.T.S is about 580
Mpaand 40% elongation
•Hot worked at 950
o
C (max. Temp.), good casting ability, excellent
corrosion resistance properties
•Uses: roller bearing caps, plane bearings and landing gear
components on aircraft, under water fittings, piston rods, pump rods,
valves, electrical applications, cables, architectureetc
24

25. THANKYOU
25
Special Thanks to:
Dr. Md. Abdullah Al Bari
Assistant Professor
Department of Mechanical Engineering,
Khulna University of Engineering and Technology (KUET)