MFI ATS_Guide, manual of install and setup for ATS tool

MFI ATS tool

1. Accessory Test System Guideline GEN7 TRAINING Viet Nguyen 20220512

2. Agenda Prepare Software package and Hardware for ATS How to install required SW packages How to set up HW connection Starting an ATS Capture How to get link key ATS User Interface MFi Test Procedure Accessory Certification Assistant 1

3. Prepare Software package and Hardware for ATS Software package ATS 7.8.1.zip ATS Utility (Link Key) 2.4.3.zip https://idmsa.apple.com/IDMSWebAuth/classicLogin.html?appIdKey=393f377d512d857e3afd5b297af56b5e66825a22397b1b788e4bb6690994f4e2&sslEnabled=true&rv=1&path=/MFiWeb/signin.action Hardware MAC PC: macOS 10.15 or later. BPA100 : https://fte.com/products/bpa100.aspx Apple handheld device in this list: iOS 13.0 or later. 2 iPad (9th generation), iPad Pro 12.9-inch (5th generation), iPad Pro 11-inch (3rd generation), iPad (8th generation), iPad Pro 11-inch (2nd generation), iPad Pro 12.9-inch (4th generation), iPad Pro 12.9-inch (1st generation), iPad (6th generation), iPad (5th generation), iPhone 11 Pro, iPhone 11, iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 13 Pro, iPhone 13, iPhone 12 Pro, iPhone 12,

4. How to install required SW packages ATS 1. On MAC, Double-click on “ATS 7.8.1.zip”. There will be new “ATS 7.8.1” generate folder include ATC application and Use Guide document. 2. Double-click on “ATS” to run it. 3. At the first time for BPA100 using, please plug in to MAC PC. Then, on ATS app, choose Wireless tab, tick on ComProbeBPA . There will be new window to ask for driver update. Then, click Install button to update. 3

5. How to install required SW packages ATS Utility 1. Unzip the file “ATS Utility (Link Key) 2.4.3.zip” 2. Connect your device to your computer 3. Launch Finder and open your iOS device in "Locations" 4. Drag "ATS Utility ( CarPlay ). ipa " or "ATS Utility (Link Key). ipa " to your iOS device 5. Follow the appropriate installation instructions below 6. Trust the "Apple Inc. - Bluetooth Test Tool" enterprise distribution profile: Open the Settings app and go to "General" > "Profile & Device Management" > "Apple Inc. - Bluetooth Test Tool" and tap "Trust". y) 2.4.3.zip 4

6. How to set up HW connection Configure the equipment as shown. 5

7. Starting an ATS Capture To begin a Bluetooth capture with ComProbe BPA analyzer, a link key is required. When configuring a capture with ComProbe BPA analyzer make sure to turn the Apple device's Bluetooth off before starting the capture. Click “ start capture ” on ATS app. Once the capture has begun, turn the Apple device's Bluetooth back on , connect to your accessory, and begin using it. 6

8. How to get link key ATS Utility (Link Key) provides a table of Bluetooth link key. 7

9. ATS User Interface 8

10. ATS User Interface Analysis begins immediately after the document is created through the "New ATS Capture" window; it is invoked via File > New > Capture…, or by pressing Command-N. 9

11. Turn off Apple device Bluetooth Start an ATS Capture Turn on Apple device Bluetooth Scan this barcode to pair with an Apple device using SPP. Scan this barcode to disconnect the connection. See the report in ATS user interface MFi Test Procedure 10

12. Device to Accessory: Search for an accessory from the device and initiate pairing. Reconnect from Apple Device: Toggle the Bluetooth connections off and on using the Control Center. Go to: Settings > Bluetooth. Reconnect to the accessory from the device. Reconnection should be successful. Disconnect from accessory Reconnect from accessory Disconnect from Apple Device Other case of MFi Test 11

13. Choose Accessory Certification Assistant Make sure your firewall settings allow you to access the ATS server at: Domain: bogart.apple.com, selfcert.apple.com Port: 443 Accessory Certification Assistant 12

14. Use your Apple ID credentials that were registered with the MFi program to access the Certification Assistant. Accessory Certification Assistant 13

15. Creating a New Certification Configuration Specify all of the accessory's connectors. Accessory Certification Assistant 14

16. Testing Your Accessory and Submitting Results This screen presents a list of tests you will need to perform with your accessory and summarizes any test results that you have generated so far. You can perform the tests in any order Accessory Certification Assistant 15

17. Reviewing Past Submissions Accessory Certification Assistant 16

18. 17 Thank you!