Multiplexing : FDM

These slides cover a topic on Multiplexing in Data Communication. All the slides are explained in a very simple manner.

1. Introduction to Data communication
Topic : Multiplexing
Dr Rajiv Srivastava
Director
Sagar Institute of Research & Technology (SIRT)
Sagar Group of Institutions, Bhopal
http://www.sirtbhopal.ac.in

2. What is Multiplexing?
•Multiplexing is a technique of simultaneous transmission of
multiple signal over single data link.
•To combine multiple signals (analog or digital) for
transmission over a single line or media is called Multiplexing.
•A common type of multiplexing combines several low-speed
signals for transmission over a single high-speed connection.
•Multiplexing is the set of techniques that allows the Multiplexing is the set of techniques that allows the
simultaneous transmission of multiple signals across a single simultaneous transmission of multiple signals across a single
data link. As data and telecommunications use increases, so data link. As data and telecommunications use increases, so
traffic also increases. We can either add a new channel for traffic also increases. We can either add a new channel for
such increasing traffic or we can install higher-bandwidth such increasing traffic or we can install higher-bandwidth
links and use each to carry multiple signals. links and use each to carry multiple signals.

3. Multiplexing is done by Multiplexer
Demultiplexing is done by Demultiplexer
Multiplexer receives large no of different input signals
Multiplexer has only one link channel
Multiplexer combines all input signal into one composite
signal & then transfers it
Sometimes this composite signal is modulated as well
At the receiving end of communication demultiplexer sorts
the composite signal into its original forms
Multiplexing can increase amount of transmitting information

4. •Bandwidth of the medium has to be greater
than the linking devices
•Efficiency of utilizing bandwidth can be
achieved through multiplexing
•e.g. telephony, telemetry & FM Radio
transmission

5. 6.5
Figure: Dividing a link into channels

6. •MUX : In communication transmission systems,
mux or MUX is an abbreviation for multiplexing. It
a device that sends multiple signals on a carrier
channel at the same time in the form of a single,
complex signal to another device that recovers the
separate signals at the receiving end. The receiver
is sometimes called a demux or DEMUX.
•Channel – Portion of the link that covers a
transmission between given pair of lines
•One link can have many (n) channels
•Guard bands – unused bandwidth is called gaurd
band
•Band – range of frequency

7. Figure Categories of multiplexing
Frequency Division
Multiplexing
Wavelength Division
Multiplexing
Time Division
Multiplexing

8. Categories of multiplexing
•Frequency Division Multiplexing (FDM)
each signal is assigned a different frequency.
•Wavelength Division Multiplexing (WDM)
each signal is assigned a particular wavelength; used on optical
fibre.
•Time Division Multiplexing (TDM) :
–Synchronous TDM: Each signal is assigned a fixed time slot
in a fixed rotation
–Statistical Time Division Multiplexing STDM): time slots are
assigned to signals dynamically to make better use of
bandwidth

9. Frequency-Division Multiplexing
•Frequency Division Multiplexing(FDM) is a multiplexing
technique that uses different frequencies to combine
multiple streams of data for transmission over a
communications medium.
•FDM assigns a discrete carrier frequency to each data stream
and then combines many modulated carrier frequencies for
transmission.
•In FDM, signals generated by each sending device modulate
different carrier frequencies.
•These modulated signals are then combined into a single
composite signal that can be transported by the link.
•Carrier frequencies are separated by sufficient bandwidth to
accommodate the modulated signal. These bandwidth ranges
are the channels through which the various signals travel.

10. •Channels can be separated by strips of unused bandwidth –
guard bands – to prevent signals from overlapping. In
addition, carrier frequencies must not interfere with the
original data frequencies.
•Figure gives a conceptual view of FDM. In this illustration,
the transmission path is divided into three parts, each
representing a channel that carries one transmission.
•FDM uses AM, FM or PM Modulations
•For example, television transmitters use FDM to broadcast
several channels at once.
•FM Radio, which combines many frequencies into one
channel

11. FDM

12. Multiplexing Process
The given figure is a conceptual illustration of the
multiplexing process.
Each source generates a signal of a similar
frequency range.
Inside the multiplexer, these similar signals
modulate different carrier frequencies (f
1
, f
2
and f
3
).
The resulting modulated signals are then combined
into a single composite signal that is sent out over
a media link that has enough bandwidth to
accommodate it.

13. Figure FDM Multiplexing process

14. Demultiplexing Process
The demultiplexer uses a series of filters to
separate the multiplexed signal into its
constituent component signals. The individual
signals are then passed to a demodulator that
separates them from their carriers and passes
them to the output lines. Figure is a conceptual
illustration of demultiplexing process.

15. Figure FDM Demultiplexing Process

16. Animated Multiplexing
•http://www.mhhe.com/engcs/compsci/forouz
an/dcn/graphics/animations/08_04.swf
•url for synchronous TDM
•http://www.mhhe.com/engcs/compsci/forouz
an/dcn/graphics/animations/08_12.swf
•url for asynchronous TDM
•http://www.mhhe.com/engcs/compsci/forouz
an/dcn/graphics/animations/08_17.swf

17. ExampleExample 11
Assume that a voice channel occupies a bandwidth of 4 KHz.
We need to combine three voice channels into a link with a
bandwidth of 12 KHz, from 20 to 32 KHz. Show the
configuration using the frequency domain without the use of
guard bands.
SolutionSolution
Shift (modulate) each of the three voice channels to a
different bandwidth, as shown in next Figure.

18. Figure for Example 1

19. Example 2Example 2
Five channels, each with a 100-KHz bandwidth, are to be
multiplexed together. What is the minimum bandwidth
of the link if there is a need for a guard band of 10 KHz
between the channels to prevent interference?
SolutionSolution
For five channels, we need at least four guard bands.
This means that the required bandwidth is at least
5 x 100 + 4 x 10 = 540 KHz,
as shown in next Figure.

20. Figure For Example 2

21. Example 3Example 3
Four data channels (digital), each transmitting at 1 Mbps,
use a satellite channel of 1 MHz. Design an appropriate
configuration using FDM
SolutionSolution
The satellite channel is analog. We divide it into four
channels, each channel having a 250-KHz bandwidth. Each
digital channel of 1 Mbps is modulated such that each 4 bits
are modulated to 1 Hz. One solution is 16-QAM modulation.
Next figure shows one possible configuration.

22. Figure For Example 3

23. Analog Carrier System
•Most of the telephone companies use analog waves to transmit
their signals during transmission. They do it by using analog carrier
system to maximize their efficiency.
•Analog carrier system uses FDM technology.
•One of these hierarchical systems used by telephone companies is
made up of groups, super groups, master groups and jumbo
groups.
•In this analog hierarchy, 12 voice channels are multiplexed onto a
higher-bandwidth line to create a group.
•A group has 48 kHz of bandwidth and supports 12 voice channels.
•At the next level up to five groups can be multiplexed to create a
composite signal called a supergroup.
•A supergroup has a bandwidth of 240 kHz and supports up to 60
voice channels.

24. •Supergroups can be made up of either five groups or 60
independent voice channels.
•At the next level, 10 supergroups are multiplexed to create
a master group.
•A master group must have 2.40 MHz of bandwidth, but the
need for guard bands between the supergroups increases
the necessary bandwidth to 2.52 MHz. Master groups
support up to 600 voice channels.
•Finally, six master groups can be combined into a jumbo
group. A jumbo group must have 15.12 MHz (6 x 2.52 MHz)
but is augmented to 16.984 MHz to allow for guard bands
between the master groups.

25. Figure Analog hierarchy
Groups
Super Groups
Mastergroups
Jumbo Groups

26. Example 4Example 4
The Advanced Mobile Phone System (AMPS) uses two bands.
The first band, 824 to 849 MHz, is used for sending; and 869 to
894 MHz is used for receiving. Each user has a bandwidth of 30
KHz in each direction. The 3-KHz voice is modulated using FM,
creating 30 KHz of modulated signal. How many people can use
their cellular phones simultaneously?
SolutionSolution
Each band is 25 MHz. If we divide 25 MHz into 30 KHz,
we get 833.33. In reality, the band is divided into 832
channels.

27. Some Applications of FDM
•AM Radio
–Band from 530 KHz – 1700 KHz
–Each station BW is 10 KHz
•FM Radio
–88 MHz to 108 MHz
–Each station has a bandwidth of 200 kHz
–E.g. 92.7 MHz will tune from 92.6 to 92.8 MHz
–FM has BW 10 times more than modulating signal
•First generation mobile phones also used FDM
•Voice signal BW is 3kHz(from 300 Hz – 3300Hz)

28. Q. How much bandwidth is given to a
user at the time of call?
Answer :
FM has BW 10 times more than modulating signal
• human voice BW is 3kHz
•So BW for calling is 3khz x 10 times = 30 khz
•So BW for receiving is 3khz x 10 times = 30
khz
•Total = 30+30
= 60 KHz

29. •Advantages of FDM
–A large number of signals can be transmitted
simultaneously
–FDM does not need synchronization between its
transmitter and receiver for proper operation.
–Demodulation of FDM is easy.
–Due to slow narrow band fading only a single
channel gets affected.

30. Disadvantages of FDM
-The communication channel must have a
very large bandwidth.
-Intermodulation distortion takes place.
-Large number of modulators and filters are
required.
-FDM suffers from the problem of crosstalk.
-All the FDM channels get affected due to
wideband fading.

31. Implementation Of FDM
•FDM can be implemented very easily. In many cases,
such as radio and television broadcasting, there is no
need for a physical multiplexer or demultiplexer. As long
as the stations agree to send their broadcasts to the air
using different carrier frequencies, multiplexing is
achieved.
•In other cases, such as the cellular telephone system, a
base station needs to assign a carrier frequency to the
telephone user. There is not enough bandwidth in a cell
to permanently assign a bandwidth range to every
telephone user. When a user hangs up, her or his
bandwidth is assigned to another caller.

32. Thank You
Dr Rajiv Srivastava
Director
Sagar Institute of Research & Technology (SIRT)
Sagar Group of Institutions, Bhopal
http://www.sirtbhopal.ac.in