Chamberlain Garage Door Opener Manual

Chamberlain Garage Door Opener Installation Manual

1. ‘The Chamberlin Group. In

POWER DRIVE —<.

GARAGE DOOR OPENER
ASSEMBLY/INSTALLATION MANUAL

1 Please read this manual and the enclosed safety materials carefully!

‘= Fasten the manual near the garage door after installation.

= The door WILL NOT CLOSE unless the Protector System” is connected
and properly aligned.

= Periodic checks of the opener are required to ensure safe operation.

= The model number label is located under the light lens on the front panel of
your opener.

Ns
Omer One

POSI2KLO » 458200

There are two types of garage door openers pictured. Yours may appear slighty diferent

IMPORTANT SAFETY NOTES

This garage door opener has boon designed and tested to oler sao service provided ti installed. operate,
‘maintained and tested in sit accordanco withthe instructions and wamings contained in is manual.

en ou ses hase Stay Symbol and Signa Words ol
di WARNING the flowin pages tay wot yout th posaba 0
abus injury or death ys ot comply ih e
Mechanical warnings that accompany them, The hazard may come
tom something mach o rom cto ost, esd
¿AWARNING the warnings carly
Electrical
on ou so Mi Signal Word o o foowing pagos,
slay py meets ge
co ander a garage doo pena you dont con
CAUTION sio catan) statment hat accompany Rous

thom caret,

2. Preparing Your Garage Door... 2
Completed installation 3
Tools Needed... 4
Opener Contents. 4
Assembly Hardware. is
Installation Hardwar 5
Assembly 68
Installation

Instalaton safety instructions.

Install the header bracket 0
Mount the header bracket "
Poston and hang motor unit ie
Fasten the door bracket 13
Attach door to tro. 14
Instaling the door control 15
Instaling the light bubs) 16
Electrical requiemonts 16
install tho Protector Syston” 17:18
Wire safety sensor 19
Adjustment

‘Adjust the UP and DOWN travel its. 20
‘Adjust the orcos. 21
Test the safety rovrsa sysiam. 2
Test ho Protector System 2

TABLE OF CONTENTS

Operation
Important Safety Information 2
Using your garage door opener 2
Using the walsmounted door conil 2
Care of your oponer 24
o open tho door manual 24
Having a Problem? 25
Diagnostic Chart Las
Programming

To add or reprogram an additional.

hand-held remote contol 2
To control the opener ig E
Malfunction remos. 2
To add, reprogram or

range a keyless enty PIN 2
To change an existing, known PIN 28
To so a temporary PIN. 29
To erase all codes from molor un memory 2
‘Tho remote contol battery 2
pair Parts

ail assembly pars 20
Installation parts 20
Motor unt assembly pats ar
Accessories... aa
Notes. En
Warrants - --35
Repair Parts and Service 36

À WARNING

a EPS |

PREPARING YOUR GARAGE DOOR

Before you begin:
+ Disable locks (contact your door manufacturer or
Information on disabing your door locks)
+ Remove any ropes connected to garage door.
+ Complete the following test to make sure your garage
oor is balanced and i no sticking or binding
1. Li the door about hallway as shown. Reloase tho
oor I balanced, it should stay in place, supported
‘ental by its springs,
2. Raise and lower the door to see here is any
binding or sticking.
1 your door binds, sticks, or is out of balance, call à
trained door systems technician,
ityou have a one-piece door, the instalation of your
garage door oponer wil be diront, Folow tho assembly
instructions included in is manual then proceed othe
instalation Instuctons For One-Piece Doors included with
the garage door opener.

To prevent possible SERIOUS IMIURY or DEAT

‘ALWAYS cl rained door systems techn if garage door
finds, sis, or out of balance, An unbalanced garage
oor may nat overs wen required

“NEVER ty to losen, move or adhıs garage door door
spins, cables, pul, brackets or thelr Rare, AL of
‘hich are under EXTREME tension.

«+ Dal ALL locks and remove ALL ropes connect to
‘age door BEFORE isting and operating garage door
‘pene to avoid entanglement

CAUTION

To prevent damage to garage door and opener:

“ALWAYS diable locks BEFORE intling and operating
the opener.

ONLY operate garage dor opener l 120V, 60 Ho avid
matuncton and damage.

Sectional Door ‘One-Piece Door

See addendum

3. PLANNING

Identity the type and height of your garage door. I you
have a one-plece door, follow the assembly
Instructions contained in this manual and refer to the
Installation Instructions One-Plece Door for
Installation procedures. Survey your garage area to seo
any ofthe conditions below apply to your installation.
‘Adational materials may be requ. You may ind
"helpful to refer back to this page and Ihe accompanying
Huston as you proceed wih the instalation of your
opener.

‘Depending on your requirements, nero aro several

instalation stops which may cal for materials or hardware

‘ot included in tho carton,

+ Instalan Pago 10- Look at th wall or collag above
the garage door. The header bracket must be securely
fastened fo structural supports,

+ instalaton Page 12- Do you have a finished celing in
your garage? I 60, a support bracket and additional
fastoning hardware may bo required

+ Instalaton Page 13- Do you have a ste}, aluminum,
berglass or glass panel door? Iso, horizontal and
voricalrenlorcoment is required.

+ instalation Pago 18 - Depending upon garage
construcion, extension brackets cr wood blocks may be
needed to instal sentore.

+ Instalation Page 18- Alemato loor mounting ofthe
fatty reversing sensor wil require harówar not
provided,

À WARNING

Without property working sae reversal system, persons
(partly small children) cou be SERIOUSLY INJURED or
KILLED by a losing garage dor.

‘The gap betwen Ihe tom ofthe garage dor andthe floor
[MUST HOT exceed 1/4 (6 mm) terse, te safely
reversa system may not work propery

“Teor Be ae Gor MUST rg 1 nat

ap.

+ Do you have an access door in ation tote garage
door no, Model 7702CB Outeide Quick Release ©
required: See Accessories page.

+ Look tthe garage door where it meets the lor. Any
gap between the floor and ho bottom o he door must
‘ot exceed 1/4 (6 mm). Otherwise, the safety reversal
System may not work proper. See Adjustment Step 2
Floor or door shout be repaired.

+ Tho openor should be installed above the contr of ho
oor. there isa torsion spring or center bearing plate
in he way of the header bracket, t may be nstaled
win 4 feet (1.22 m) o helt or right of the door
cent.

+ Iyour doors more than 7 fet (2.13 m) high, so rai
extension ks sted on Accessories pago 2.

‘COMPLETED INSTALLATION

5. ‘ASSEMBLY HARDWARE

os

6. ASSEMBLY CAUTION

To prevent INJURY trom pinching, Kep hands and fingers
tay rom he ans white asemblin ne al
(1) ‘Assemble the Rail i x ,

Art

67-3 FEU vu

ALL HARDWARE SHOWN ACTUAL SIZE

7. CAUTION

To 200 serous damage o opener, ONLY use ols asteners
mount la op of motor un.

[2] Remove Fasteners trom [3] ‘Attach Rail to Motor Unit [4] ‘Attach Chain Spreader
Top of Motor Unit

Où 0 Of

Aacranmaciie — Patton

ALL HARDWARE SHOWN ACTUAL SIZE

EN

8. CAUTION

To avoid possibe SERIOUS INJURY to Angers:
+ Securely attach cain spreader

Route ChainvCable Around Rall Assembly “NEVER conne garage door opener o power source ut
and Motor Unit Sprocket Insite todo So.

[Attach Chain o Talley ‘Attach Nut and Lock Insert Tolley Threaded
‘Threaded Sha Washer to Troy ‘Shaft nto Round Hoe a
Threaded Shaft Tetley

one

Desired Chan Tension

Assembly of your opener is now complete.

ALL HARDWARE SHOWN ACTUAL SIZE

On] $ O
& co

tater

9. INSTALLATION

IMPORTANT INSTALLATION INSTRUCTIONS
AA WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARRINGS AND
INSTRUCTIONS,

2 instal garage dor opener ONLY an propery lances an
Tube garage dor. An improper talanced door may no
reverse when required and could rest in SEVERE INJURY or
DE

3. AL repair to cables, spring assembles and oer hrduare
MUST be made by a tad door systems tecnica BEFORE
instaling opener

4 Disable AL ack ang remove ALL ropes connecte 1 garage
Goo BEFORE instalo opener o avi elangement

5 instal garage dor opener 7 fet (23 m) or more above loo

6 Mount emergency release handle 6 et (1 88m) above tor.

7. NEVER connect garage door opener to power source untt
Instruct 1 do 80

8. NEVER wear watts, ns o lose cota wil Insaling
or servicing opener. They could be caught in garae dor or
Opener mechanisms,

3. Insta walkmounte garage door contrat

© away rom ALL moving pats ofthe door.

10 Poze agent varia he on valet gag oar

11. Place manual rlase/saft reverse test abel in plain view on
Inside of garage door

12 Upon completion of instalation, et sat reversal system.
Door MUST reverse on contact ih a 1-12: high (2.8 em)
‘object (or 22 x4 iat) onthe Hor

I you have a one-piece door, proceed to the
allan Instructions included
with your garage door opener.

you have a sectional door, proceed to page 10
‘of this manual.

INSTALLATION
INSTRUCTIONS
FOR ONE-PIECE
D00RS.

10. INSTALLATION

INSTALL THE HEADER BRACKET

NOTE: You can fasten the header bracket within 4 foot
(12 m) ofthe lt or right ofthe door center ony it a
torsion spring or center bearing plates nthe way; or
you can attach 10 ne collng when clearance is
minimal

Fasten header bracket securely to structural supports
li may bo necessary o uso a 2 4 as a stuctural
‘suppor it nsaling on dal or betwoon mo studs as
‘shown in Step 3. Securely fasten 2x 4 lo structural
‘supports using ag scrows (not provided). Concreto
‘anchors must be used if mounting header bracket or
2x 4 to masony.

Mark the Center of the 5
Garage Door ,

Determine the Highest Point of
rave, and Draw Horizontal Line
{or Header Bracket Placement

à WARNING

Ta prevent possible SERIOUS INJURY or DEATH

Header racket MUST be RIGILY fastened to structural
Support on header wal or celing,olherwise garage door
‘might nat reverse en raue.

“NEVER ty to Hosen, move or adhıs garage door, sings,
cables, pueys, rackets, rte hardware, ALL of which ae
Under EXTREME tension.

„er bees

‘Add 024 8 a Structural Support
(necessary)

11. [4] Mark Bracket Holes © Dail Hotes © ‘Attach Bracket

DST cal
CREEL. , prem

‘Cling Mount the Header Brack (Optional)

(NOTE: If your instalation requires thatthe
header bracket be mounted o ne celing, The
‘back edge ofthe bracket MUST NOT be
unter than 6° (15 cm) trom the header wall
and the arrow MUST point away rom the
header wall

[7] ‘Attach Rail to the Header Brach

NOTE: line door spring
ls in the way, you need
help. Have someone hold
nn the opener securely ona
{temporary support to alow
‘heal fo clear the spring.

cg TOOT D JO O

ACTUAL SIZE
ETES Crea CR Fase Case

12. à WARNING
POSITION AND HANG MOTOR UNIT | 192.0% possible SERIOUS JURY rom a ating garage door

Opener, sent securely to structural supports ofthe garage

Open Dor to Ful Open Postion and Rest Ral AUTION
‚on a 2x4 to Position Opener at the Proper ci
Ace for Hanging rom ne Gang To reset dae 1 gage po et ape or peer

raten 2x4 placed on top section a dor.

tthe top section or panel his the trolley when you raise
the door, pul down on the trol release arm lo
<dsconneet inner and outer sections. Side the outer rly
toward the motor un. The roloy can remain
‘dsconnected unt instalation is compete.
NOTE: The garage door opener motor head wil typicaly
Ait lomer than the header bracket, therefore, tho rad wi be|
atan angie.
[2] "Attach Hanging Brackets to Ceiling and Fasten Motor Unit to Hanging Brackets

NOTE: Bofro tho motor units sacurad othe calng, insure that tho motor unit and ral aro centered

‘ver the door Ifyou mounted the header bracket of center, hang the motor uni the same distance.
Concrete anchors must be used nstaling any brackets into masonry.

Option with tished or unfiished cong Option wi untnishad coling

"ALL HARDWARE SHOWN ACTUAL SIZE

Ce CS cm Cres

=

13. CAUTION

Ta prevent damage to garage door, reines inside of dor
wath angle on Bob ertealy an horzotly.
HORIZONTAL AND VERTICAL REINFORCEMENT]

Horizontal and vertical enforcement (not provided) i
naodod fr light weight garage doors (iberglas,
‘Suminum, see, doors wit glass panel ete),

AA horizontal reinforcement brace should belong
‘enough o be secured o wo or tree vertical
Supports. A vertical elnorcement braco should cover
{the halgh of th op panel. Contact your door
manufacturer for more information regarding,
reinforeement of your dor.

Many door reinforcement kts provide for ect
attachment ofthe clevis pin and door arm. In is
so, you wil not need the door backe: proceed to
Connect Door Arm to Talley section.

FASTEN THE DOOR BRACKET

(1) Position Door Bracket

Position the door bracket on
=== be taco ofthe door wahin tho

olla inte

1.Tno top edge of tho bracket

2-4 (5-10 cm) below the
top edge of he door.

2.The top edge of the bracket
directy below any structural
‘suppor across the op of
the door

Lapel T Handırane
[or g D ‘SHOWN
acTuaL Sze
>

NOTE: Tho 1/4"-14 x 58" sol-reading screws
aro not intended for use on wood doors.

14. À WARNING

‘ATTACH DOOR TO TROLLEY,

(1) ‘Attach Emergency Release Rope and Handle

To preven ose SERIOUS JU DEATH om ling,

uae soo

‘posse, use amare reas anoto soe troy ONLY
‘han gap dor CLOSED, Wes or ron eps o
ne 600 could est an pen ong apy or
epee

“EVER use emergency sa ane unes garage dr is
Cha aprons ad übten

“NEVER use todito pal or open or aed rope at
canos sie you Cou al

NOTE: Hando should hang 6 feet (1.5 m) above floor
Ensure hat he rope and handle clear the tps ofa
vehicles io avoid entanglement.

CONNECT DOOR ARM TO TROLLEY

Pull Emergency Relea
the Trey

Rope to Disangage

Slide Tol Back 2° (5 em) and Connect Straight
Door Arma the Tolley

[4] ‘Connect Curved Door Arm to the Door Bracket

Ensure Door is Fully Closed and Connect
oor Ame

ALL HARDWARE SHOWN ACTUAL SIZE

O

06 ne Fate

© ©

stumm came

1

15. AM WARNING
To prevent posible SERIOUS INJURY or DEATH from
ekctrocutor
Be sure power is not connected BEFORE isting Door
Conta
= Connect ONLY to 24 VOLT low voltage ru.

Connect wire to

5° | rn sb SEROUS MAUR or EN om acing
age door
Ina Door Cont win Si of garage dr ut of reach
ele ta minimum ag of ft (18m) and ay
se rom al moving prt of oo
Bon NEVER permit ern 1 operator ly wth dor cn
a sh los or emote canal transmite
ene | tan dor OAL when can be seen cay. propery
4 ma, | aust. andere re no ista rar tae
fesse + AWAYS keep garage cor shut comp ase
Ez, - EVER Dar ora to rss pa a dosing pra dr

Position Door Control, Route Door Control Wire to
Motor Unit and Secure with insulted Staples.
Permanently Mount 2 Safety Labels Using Adhesive
‘aching, Tacks or Staples, Necessary.

Ccaretuty Remove Cover
Mu-Funetion Door

9er

© ‘Attach Door Control to Wall and Replace Cover

¡Connect Door Control Wires

cs er joe
ES ac)

AUCHARDWARE SHOWN ACTUAL SIZE

oD (= tt (©

E Ns E Cu

16. CAUTION

To prevent posible OVERHEATING othe enpanel or
light socket

«DO NOT use sor neck or special ght bubs

+ DO NOT use halogen bulbs. Use ONLY incandescent
To prevent damage othe opener

+ DO NOT use bulbs larger an 100

+ ONLY use At size bubs

STALLING THE LIGHT BULB(S)

recto inate) mmunimonm () in stag ue
m © CAES

Cy Santee gO.
DD

WARNING

ELECTRICAL REQUIREMENTS pren pose SERIOUSLY or EAT rom
tig Motor Unt nto Power +e sure por is NOT conecte o Me apner and
Ose Sie campo ist TON covet

stabs permanent wring conection.

+ Garage door instalation and wing MUST be in compliance
‘ih ALL Teal lect and bung codes

‘NEVER use an extension cod, 2 ie adapta, or chango plug
"ANY way to make toute. Be sre the opener
ground

BE]

NOTE: Plug motor un into grounded power out. la grounded outlet is not available, contact a quad
alectrcian 16 Instala proper outlet.

A permanent wiring is required by your local code, follow procedure below. Disconnect power to the
cireult before removing cover to establish permanent wiring connections.

Remove Motor U Remove Power un Wire from Replace Motor Unt
Serows and Cover Cord Outlet to Motor Unit (Cover and Serews.

17. à WARNING

A o pio SERIOUS INJURY 0 DEATH om à closing garage

INSTALL THE PROTECTOR SYSTEM

‘The safety reversing sensor must be connected and
aligned correctly before the garage door opener wil
move in the down direction.

NOTE: DO NOT operate the opener at tis time.

IMPORTANT INFORMATION ABOUT THE SAFETY
‘REVERSING SENSOR

on propery connected and aligned, Ihe sensor wi
detact an obstacte in the path oli olgcrnic boar. The
Sondng oyo (with an ambor indicator Hoh) ana an
invisible ight beam to ho receiving eye (with a green
indicator igh). I an obstruction breaks the light boar
le the door is closing, the door wil stop and reverse to
{ull open positon, and the opener lights wil lash 10 times.
‘Tho units must be installed inside the garage so that the
soning and receiving eyes face each other across the
door, no more than 6 (15 em) above the floor. Ether can
be instalo on tho lft or right ofthe door as long asthe
Sun never shines directly ino the receiving eye len,

‘Tho mounting brackot are designed to cp nto tho track
of sectional garage doors without additonal hardware

seer
Corel connect and ln ne satety reversing sensor. This
regule safe device MUST NOT be disabled

‘Insta he safety reversing senor so beam is NO HIGHER.
than 6 (18 em) above grape loa.

litis necessary to mount the unis on he wal, the
brackets must be securely fastened to a sold surface
such as tho wal framing, Extension brackets (500
Accessories) are avaiable if needed. stating in
masonry construction, ad a paco of wood at each
Tecaton to avoid dig extra holes in masonry it
reposioning is necessary.

‘Tho invisible ght beam path must bo unobstructed. No
pat ofthe garage door (or dor tracks, springs, hinges,
Folors or ohor hardware) may interupt the Boam while
the door is closing,

genre mati pt tan

Facing the door from inside the garage

18. INSTALL THE PROTECTOR SYSTEM

11] Assemble Safety Reversing Sensors [2] Mount Brackets
age rc tos peered

Mount Brackets: Mounting Options
@ Poor nta tor) © mt promo © sm in rn

NOTE: The safety rovorsing sonsor must
be connected and aligned correct below
‘he garage door opener wil move nthe
‘down dect.

ALL HARDWARE SHOWN ACTUAL SIZE

19. WIRE SAFETY REVERSING SENSOR

© Ber sey senor reo motor unt and see
‘th insulted Staples

ALL HARDWARE SHOWN,
ACTUAL SIZE

20. ADJUSTMENT

À WARNING

e NE od sale rvesa system, persons

ADJUSTMENT STEP 1

‘ADJUST THE UP AND DOWN TRAVEL LIMITS

Limit acjustmont satings rogulatotho points at which tho

door wil stop when moving up or down.

To operat tho opener, press Ih door control push bar.

Fun the opener through a complete travel cyt.

+ Does the door open and close completely?

+ Does the door stay closed and not reverse
unintenionaly when tly closed?

lt your door passes both ofthese tests, no Hit

adjustments are necessary unless tho reversing ost ais

(606 Adustmont Stop 9).

‘Adjustment procodures are outined below, Rad tho

procedures carelly before procaeding to Adjustment Step

2. Use a strewerivr to make lent adjustment. Run the

‘opener through a complete travel cyte alor each

adjustment

(NOTE: Repeated operation of the opener during

achusimont procedures may cause the motor to overheat

‘and shut of. Simply wait 15 minutes and ty again,

NOTE: I anything intortoros with the doors upward travel,

wi stop. anything nterores wäh the doors downward

travel (including binding or unbalanced doors), il

HOW AND WHEN TO ADJUST THE LIMITS

the door does not open completely but opens at

least 5 toot (1.5 mp
Increase up travel. Tum the UP lit adjustment eer
clockwise. One tum equals 2° (5 om) of travel
NOTE: Te provent the toy from hiing tho cover
protection bolt keep a minimum distance 024°.
(5-10 cm) between th toloy and the bok,

I door does not open at least 5 feet (1.5 m):
‘Adjust the UP (open) force as explained in Ajustmant
Step 2

+ Ifthe door does not close completely:
Increase down travel. Tum the DOWN Im adjustment
screw counterclockwise. One tum equals 2 (6 em) of
travel.

(particularly smal chien) could be SERIOUSLY INJURED or
KILLED bya casing garage door

‘Incatectagjustment of garage dor rave its wil interfere
th proper operan of Saey reversa system.

«Ine contr (rc o ave its) sade, the other
control may ls ned adjustment

Atar ANY austen ar made, he safety reversal system
‘must be ested. Dor must ers on contac wih 1-12
(8.8 em) high jet (or 2x4 taa fia) on oor.

CAUTION

To prevent damage to veis, e sure uly open door
proves adequate cearace

¡Spy

9er

+ Ifthe opener reverses in fu closed position:
Decrease down travel. Turn the DOWN limi adjustment
screw clockwise. One tum equals 2 (5 cm) of Favel.

+ Ifthe door reverses when closing and there is no
visible interference to travel cycle
Ifthe opener lights ae flashing the Safety Reversing
‘Sensors are ofher not installed, misaligned, or
obstructed

21. à WARNING

ADJUSTMENT STEP 2
‘ADJUST THE FORCES

Force adjustment controls are located onthe back panel
ofthe moter un. Forco adjustment sotings reguat tho
[amount of power required to open and close the door.

I the forces aro set 10 light, dor travel may bo
interupled by nuisance reversa in the down direction
and stops inthe up dection, Weather conditions can
‘affect No door movement, 0 occasional adjustment may
be needed

‘Tho maximum force adjustment range is about 44 ofa

haut a propery install salt eversal system persons

(particularly smal ern) could be SERIOUSLY INJURED or

FILLED by à closing garage dor

‘Too much force on garage door wil intrtere wih proper
operation of safety reversal system.

EVER increase force beyond minimum amount requir to
‘ose garage door

EVER use fre djusiments o compensate fra binding or
cg garage door

«It ne control (rc or aval lis) s adit, the oter
control may also need adjustment

Mar ANY austen are made, the al) reversal system
‘must be std. Door must reverso on conc wih 1-1/2
(88 cm) high jet (or 24 taa) on oor.

complete tun. Do not force controls beyond that point
‘Tur force adjustment controls wih a screwdriver

NOTE: I anything intrlres with the doors upward rave,
wi stp. N anything ntereres wäh the doors downward
travel (including binding or unbalanced doors), it wil

HOW AND WHEN TO ADJUST THE FORCES

Tost the DOWN (close) force
‘Grasp tho door bottom when the door is about halray
through DOWN (close) travel. Tho door should verso.
Rovorsal halfway though down tavol does not
guarantee reversal on a 1-1/2" (3.8 om) obstruction. Soo
Adustmant Step 3, page 22 {ne door is hard to
hold or doesn't reverse, decrease the DOWN (cose)
force by tuning the contra counterclockwise. Make
‘small adjustments unt the door reverses normaly. Ater
(ach adustment, run the opener through a compte
yoo.

+ Ifthe door reverses during the down (close) cycle
and the opener lights arent flashing, Incroaso DOWN
(close) ore by tuming ho contol clockwise. Make
mal adjustments unt the door completes a cose
ice. Aller each adjustment, run the opener through a
complete travel cycle. Do nol increase tho force beyond
{he minimum amount required o cose the door.

2.Test the UP (open) force

* Grasp the door bottom when the door is about hatway
through UP (opon) travel. The door should top. the
‘door is hard to hold or doesnt stop, decrease UP
(open) force by tuning the contro! oountereickwse,
Make smal agustments unt the door stops easily and
opens fuly fer each adjustment, run the opener
through a complet travel cyte,

+ Ifthe door doesn't open at least 5 feet (1.5 m).
increase UP (open) force by tuning the control

Clockwise. Make small adjustments ul door opens

completo, Readjus tho UP limit necessary Ar

each adustment, run the opener through a complete
travel cycle.

a

ey
[y

te) te)
fe) fs
=‘

22. à WARNING

EV. ODA Instale salt reversal sien, persons

ADJUSTMENT STEP 3

TEST THE SAFETY REVERSAL SYSTEM

Test

+ Wah the door luly open, place a 1-1/2" (8.8 cm) board
{or a 2 x 4 laid flat) on te floor, conterd under the
garage door.

+ Operate te door in the down direction. The door must
reverse on striking the obstruction.

Adjust

+ Nine door stops onthe obstruction, itis not traveling ar
‘enough in the down direcion. incoaso the down travel
by turing the DOWN iit adjustmant crow
countercockise 14 tum.

NOTE: On a sectonal door, make sure iit adustments
do not force the door arm beyond a Siaght up and
‘down position. See page 14

+ peat the test.

+ When the door reverses on the 1-1/2" (38cm) (or a 2x4
lai fat) boar, remove the obstruction and run the
‘opener through 3 or 4 complet ravel cycles o ost
adjustment.

TEST THE PROTECTOR SYSTEM

+ Press the remote control push button to open Ihe door

+ Place the opener carton in the path of he door.

+ Press the remote contol push button 1 close the dor.
‘The door wil not move more than an inch, and the
opener lights wil lash,

“Tho garage door opener wil not close from a remote it the

indicator ight in other sensor of (ring you tthe fact

{hat no sonsor is misalgned or obstructed)

ithe opener closes Ihe door when Ihe say reversing

‘sensors obstructed (and the sensors are no more than

6° (25 mm) above tho for), cal fora tained door

systems technician.

(parlar smal chien) could be SERIOUSLY INJURED or

KILLED bya closing garage door

+ Safety reversal ste MUST be tested every month

one control (rc or ave limits) sadist, the other
col may also need adjustment

After ANY agustments are made, the alt reversal system
‘must be tested. Door must reverse on cont with 1-12"
{8 em) gh jet (or 2x4 ta fa) onthe foot.

12 aes bar raed wo

A WARNING

that a proper installed sat eversng sensor persons
(parlar smal ern) coul be SERIOUSLY INJURED or
FILLED by à closing garage door.

Se on ae ‘Sey vo ese

23. OPERATION

IMPORTANT SAFETY INSTRUCTIONS

1 READ ANO FOLLOW ALL WARNINGS AND INSTRUCTIONS.
2. ALWAYS kop remote controls ut ofeach ohren. NEVER
permit chien to operate a play with garage dor contro

Push butons a remote contol

ONLY activate garage dor when can be sen lay its

Propery ajustes, and there are no abinucons to dor ve,

ALWAYS keep garage door in sight ut completely closed. NO

ONE SHOULD GROSS THE PATH OF THE MOVING DOOR,

NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPEN

DOOR.

6.1 possible, use emergency release handle t disengage trolley
ONLY when garage Gor CLOSED. Weak or rokan springs
for unbalanced dor ou result an open door ala apy
andor unexpected

NEVER use emergency rolas hand unes garage doorway
Is clear a persons ang obstuctons

8. NEVER use handle to pol garage door open or cose. ope
nat becomes uted, you cul fal

AA WARNING
To reduce the risk of SEVERE INJURY or DEATH

8. on contol (lore or tal miss adjust te other
conto may also need adjustment

10 Aer ANY adjustments are made, the saley reversal sytem
MUST be tested

11. Safety eersal system MUST be estes evry month. Garage
door MUST reverse on contact with 1-1/2 (38 em) obec,
or à 2x4 laa fa) on te oe

12 ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED (see
page 2). An improper balanced door may NOT reverse
en required and coud result in SEVERE INJURY ar
Dea

1. ALL repairs to cates, sping assembles and oter hardware,
ALL of whieh ae under EXTREME lenin, MUST be made
bya tained door systems tecnica.

14 ALWAYS disconnect ct power 1 garage door opener
BEFORE making ANY repars or removing coves.

15 SAVE THESE INSTRUCTIONS.

USING YOUR GARAGE DOOR OPENER

Your Socurty#*openor and hand held remote contro!
have been factory. se o a matching code which changes
with ach u, randomly czas over 100 ion naw
‘odes, Your opener wi operate wath up 1.

Sccutiy amena corre and one Seca Koyess

Enty System. you purchase a new remote, orf you

wish 1 deactato any remoto, flow te instructions in

the Programming secon

‘Activate your opener with any of the following

+ The hand-held Remote Contol: Hold the pushbutton
own unt the door sats to move.

+ Tho wal-mounted Door Control Hol the push button or
bar down unt the door stars 10 move.

+ The Koylss Entry (See Accessories): provid with
your garage door opener, must be programmed before
use. Soo Programming,

When the opener is activated (withthe safety

reversing sensor correctly installed and aligned)

1.1 open, the door wil coso. closed, it wil open.

2.1 losing, the door wi reverso.

3.1 opening, the doce il top.

he door has been stopped in a parlaly open poston,
It wi ose,

5. obstrutod while closing the door wil rovers. tthe
‘struction intrupts the Safely sensor bea, tho
‘panerights wil ink or Ivo seconds.

6.1 obstructed while opening, the door wit sto.
7.1 fly open, the door wi no close whan the sat
‘sensor boam is broken. The safety sensor has no elect
inthe opering oy.
the safety sensor isnot instale, ois misalgned, the
‘door ont cose rom a hand-held remote. However, you
‘can close the door wih the Door Cont, tho Outside
Keock, or Koyless Entry, you activate thom until down,
travel is complet. I you release them too soon, the door
wil overs.
‘The opener lights wil tum on under the folowing
concis: when the opener is naly plugged in; when
power is restored after interruption; when the opener is
actvated.
"hoy wl tun off automatically ator 4-1/2 minutes or
provide constant ight when te Light feature onthe
Mut-Funcion Door Control is actvated, Bub size is A10
© 100 watts maximum.
light feature: Lights wil also tum on when
someone walks trough the open garage door. With a
Mult-Function Door Contr, this feature may bo tumed off
as folows: with ho oponer igh’ of, press and hola tho
light butonfor10 seconds, unt the ght goos on, hon of
again. To restore hs feature, sar wii the opener ighte
‘on, then press and hold the fight button for 10 seconds
Uni he ight goes of, then on again

24. USING THE WALL-MOUNTED DOOR CONTROL

‘The Multi-Function Door Control LA
Press the push barpush button to open or tes
close the door. Press again to reverso the Sn
‘door during the closing cycle orto stop the. Lod
¿door while I's opening,

Light Feature ea,

ross the Light buton to um the opener

light on or of. I wit at control the opener

lights when the door is in motion I you tum ¡Lon and then

acivato Ih oponer, Ihe ight wil romain on for 4-12

‘minutes. Press again to um I of sooner. The 4-12 minute

Interval can be changed to

1-12, 2472, or 3-12 minutes as follows:

1 Press and hold the Lock button until the ight binks
(about 10 seconds). À single Bink indicates that the
timer is reset to 1-1/2 minutes.

2. Repeal the procedure and the ight wal ink ui,
resetting the timer to 2-1/2 minutos.

3.Repaat again fora 3-172 minute interval, ele, upto a
maximum of four inks and 4-1/2 minutes,

Lock Feature

Designed to prevent operation ofthe door from hand-hes

omoto contls. However, ho door wil open and close

{tom tho Door Control, ho Oido Koylock and the

Keyless Entry Accessories.

To activate, press and hold the Lock button fo 2 seconds.

‘The push bar ight wil ah as ong asthe Leck feature

To tum of, press and hold he Lock button again for

2 seconds The push bar ight wil stop flashing. The Lock

feature wil also um off whenever ho “Lear Button on

{the motor unit pane is activated,

TO OPEN THE DOOR MANUALLY

‘Tho door should be fly close if possible. Pull down on
{he emergency release handle and lit the door manual
To reconnect the door o he opener, press the door
contol push bat

‘Tho lockout feature prevents the toley rom reconnecting
úautomatcaly, pull the emergency release handle down
and back (oward the oponer), Tho door can then be
raised and lowored manually as fon as nacossary To
tisengage the lockout featur, pull the handle sraight
‘own. The trolley wl recomect onthe next UP or DOWN
person

CARE OF YOUR OPENER

RICA

Limit and Force Adjustments

‘Weather conditions may cause some

minor changes in dor operation requing

some readjustments, particulary during

the fst year of operation,

Pages 20 and 21 refer othe Imit and

force adjusimonts. Only a serewarver is

required. Follow the instructions carotly.

Ropeat the safely reverse tst (page 22) tor any

adjustment of Imis or forces.

Maintenance Schedule

Once a Month

Manual operate dor. I is unbalanced or binding. all
a traned door systems techmician

+ Check tobe sure door opens and closes fully Adjust
las andor 110 it necossan

‘+ peat tho safety reverse tet. Mako any necessary
adjustments

Twice a Your

+ Check chain tension, Disconnect rally rl. Adjust it
necessary.

Once a Year

+ 01 door rollers, bearings and hinges. The opener does
ot require adiiona kircaion. Do vot grease door
tracks

WARNING

To prevent possbe SERIOUS INJURY or DEATH Tom a ling

garage door

* I possible, use emergency release Rand 1 isngage
alle ONLY wen garage doors CLOSED. Weak or broken
sings or unbalance door cau res in an pen dor
{ang rail andlor unexgectely.

+ NEVER use emergency release handle unless garage
doorway i clear Of persons and obstruction.

+ NEVER use angle o pl dor ape or closed rope not
becomes und you cul fal

25. HAVING A PROBLEM?

1.My door will not close and the light bulbs blink on
my motor unit: The safety reversing sensor must be

‘connected and aligned comecty before tho garage,

or opener wil move inthe down direction

+ Vary tho safety Sensors are propery installed,
aligned and reo of any obstructions. Refr 10
Instataton Stop, Instal The Protector System.

+ Chock diagnostic LED for flashes onthe motor unit
‘han refer tthe Diagnostic Chat on the flowing
page.

2.My remotes will not activate the door:

Very your Muti-Function door conto isnot
inkl. I is bling, deactivate the Lock Mode
folowing thoinsructons for Using the
Multi Function Door Control.

+ Roprogram remotes flowing the programming
instructions, Retero Programming

+ remote wil stl not activate your door, chock
agnostic LED for flashes on motor unt hon rotor
10 Diagnoste Chart on the folowing page.

3.My door reverses for no apparent reason: Repeat
salety reverse test after agustments to force or travel
mis: The need for occasional adjustment forthe
force and limit stings is normal. Weather conditions
in particular can act door travel.

‘+ Manualy check door for balance o any binding
problems.

+ oer to Adjustment Step 2, Adjust he Forces.

My door reverses for no apparent reason alter
tul closing and touching the floor: Repeat safety
reverse tes aor aghstmonts 1 force or travel mis

“The nood for occasional adjustment forthe force and

limit stings Is normal. Weather conditions in

particular can ec door trav

+ ler to Adjustment Step 1, Adjust the UP and
DOWN Travel Limits. Decrease down travel by
turning DOWN limit adustment screw clockwise

ae E

5.My lights will not turn oft when door is open:

+ The garage door opener i equipped wih a security
light feature. This feature activates the ight on
von the sale sensor beam has been obstructed,
Rotor o Operation section; Using the Wall Mounted
Door Control, Light Feature

{6.My motor unit hums briefly:

+ First vorty thatthe oly is against he stop bot

+ Release the door rom the oponer by puling the
Emorgoney Release Ropa,

Manual bring the door o a closed postion.
+ Loosen the chain by adusing the outer nut 4 105
ums, Ts roves the tension.

+ Run the motor un rom the remote contro or doce
control The troley shou travel towards the door
and stop I the Valley ro-angages with to door,
pull the Emorgoncy lease Rope to disengage

+ Decreaso the up travel by turing the UP Travel
adjustment serew 2 ful toms away trom Ihe arrow.

+ Ifthe trolley does not move away trom the bot,
repeat the stops above,

7.My motor unit clicks:

* Motor is overheated, low 15 minutes for motor to

cod and try again

26. DIAGNOSTIC CHART

Sale reversing
‘sensors wire shorted
‘or bledo wire
reversed,

oR

2 FLASHES

Satoy rversing
‘sensors wire open
(broken or
connected),

3 FLASHES

Door contra or
wre shorted,

“Say Reversing
Sensors sigh
‘misaligned (dm or
flashing LED).

5 FLASHES

Motor overheated
or possible RPM
Sensor aire.
Unplug to reset

Motor Circuit Faire.
Replace Receiver
Logie Boars.

Your garage door opener is programmed with
seldlagnosic capables. The "Learn" bunor/dagnostio
LED wit fash a number of times then pause signiyingit
has found a potondal issue. Consul the Diagnose
Chart below.

Le Symptom: One or both ofthe Indicator lights on the safety sensors do
not glow steady.
+ Inspect sensor wires fora shot (staple in wir), coract wing polrty
(Glackivhte wires reversed), broken or aisconnected wires, replacolatiach
as needed.

+ Disconnect al wies from back of motor un.

+ Remove sensors from brackets and shorten sensor wies to 1-2
(0-60 em) rom back each of sensor.

+ Reattach sending eye to moter unt using shortened wies. I sending eye
indicator ight glows steal, attach Ih recevng eye.

+ Align sensors, if the indicator gts glow replace the wires forthe sensors. I
‘the sonsorindicator lights do not ight, replace the saely sensor.

Le Symptom: LED ls not it on door control.
+ Inspect door controles fo a shor (staple in wie), roplaco as needed

+ Disconnect wros at door contro, touch wires together. motor unt
acivaes, replace door contr

+ tf motor unit doesnot activate, disconnact door control mire from motor
Unit Momentariy shor across red and white terminals with jumper wr. I
‘motor unit activates, replace door control wires.

+ I motor unt doesn't operate, motor unt is overneated. Wat 15 minutes and
‘ety. I moor unt sl wl ot operate replace loge board

[© Symptom: Sending indicator light glows steadily, receiving indicator ight
is dim or flashing.
+ Realign recoving aye sensor, clean lens and secure brackats
+ Vey door track is my secured to wall and doos not move,

[© Symptom: Motor has overheated; the motor unit does not operate or
{rolle is stuck on stop bolt = Motor unit hums briefly; RPM Sensor =
‘Short travel -8" (15:20 em.

+ Unplug unt to rosal Try to operate motor unt, check diagnostic codo.
+ Hits til ashing 5 tines and motor vit moves 6-8 (15:20 em), replace
RPM sensor

{© symptom: Motor unit doesnt operate.
+ Replace logic board because motor rarely ais.

»

27. PROGRAMMING

TO ADD OR REPROGRAM AN ADDITIONAL HAND-HELD REMOTE CONTROL

NOTICE: 1 this Socuriy# garage door opener is operated with a non-roling codo ransmitr, the technical measure in
the receiver! the garage door opener, which provides securty against code-thelt devices, wil ba circumvented. The
‘owner ofthe copyright in the garage door opener does nor authorize the purchaser or supplier ofthe nonoling code
transmiter io creumvent that technical measure,

Your garage door opener has already been programmed a he factory to operate with your hand-held remote control
‘Tho door wll open and close when you press the push button.

Below ae instructions for programming your opener to operate wth adsitonal Security” remote controls.

Using the “Learn” Button Using the Multi-Function Door Control

1. Press and release tho “earn” button on

{ho motor unt. The lar ndclor Et
2. While hing the mote buton, press
vel glow tsar or 30 seconds.
> u and old tho ight btn onthe

2. Within 30 seconds, press and hols the Muti-Funetion Door Control W
ton onthe hand-held remoto" hat
= mandhadremasıust., |B 3. Continue hoking both buttons while you

OU wish to operato your garage doer.
iaa press the push bar on the Mute Function
3. Release the button when the motor Door Control (al re butions are hela).

{nights ink. ha loomed the

Code. ight bulbs are not insta 4. Release buton when the motor unt

a ed fights bin. thas lame in code I
light bole are nt nal wo lt
willbe near

‘porate your garage door

CE F=5
oe ee
\

TO CONTROL THE OPENER LIGHTS

*3-BUTTON REMOTES.

Only available with Multi-Function Door Conte 1 provided wih your garage door opener, the large
In addtion to operating the door, you may button factory programmed o operate Additional
Program the remot to operat th ight. ZZ) vistors on any Socurty”
1. With the door closed, press and hold a mul tuncion remote or >

small emote button hat you want to contol minisemote can be ZA

tho ight ogame opera ZEN 7
Press and hold the Light button on the Multi-Function tr Sesurt
2. Bras and hod the Ugh buon on the Mulan Elena

3. Wii holding tho Light button, press and hold tho Lock
button on the door control

4. Alto tho oponor lights fash, release al buttons.
a

28. TO ADD, REPROGRAM OR CHANGE A KEYLESS ENTRY PIN

NOTE: Your new Keyless Entry must be programmed to operate your garage door opener

Using the “Learn” Button

1. Press and release the “ear” button
on motor unit The leam indicator ight
‘sl glow steady for 30 seconds.

2. Within 30 seconds, entera four dit
personal identification number (PIN) of
Your choice on ho Keypad. Thon press
nd hold the enter button,

3. Release the button when the motor
uni ights bink. I has leamed the
code. I ight bubs are not installed,
two cicks wil be hoa,

Using the Mult-Function Door Control

NOTE: This method requires two peopl i the Koyless

Enty is already mounted outside tho garage.

1. Entor a four digit personal demication
number (PIN) of your choice onthe
keypad. Then press and hold enter.

2. While holding the ENTER buton, press
and hold the LIGHT button onthe
Muti-Functon Door Contr

3. Continue hoking the ENTER and LIGHT
bultlons while you pross th push bar on
the Mult-Function Door Contrl (al three
buttons are hel}

4, Roloase buttons when the motor unit
lights Bink. has eared the code.
ght bulbs are not instala, two cis
ile heard.

TO CHANGE AN EXISTING, KNOWN PIN

Ifthe exiting PIN is known, it may be changed by one
person without using a ladder
1 Press the four button or the present PIN, then press
and hold the # button
“The opener light wil Bnk twice. Release Ihe # button,
2.Press the now 4-dg PIN you have chosen, then
press Enter.
“The motor unit gts wil ink once when the PIN has
been leamed.
“Test by pressing the new PIN, then press Enter. The door
shoud move,

lif

29. ‘TO SET A TEMPORARY PIN

You may authorize access by vistors or service people
witha temporary 4-aigit PIN. Altera programmes number
‘of hours of numberof accosses, this temporary PIN
‘xpios and wil no longer open the door. It ean bo used to
ose the door even aer has expired. To st a
temporary PIN:
1 Press the four buttons for your personal entry PIN
(cot the lat temporary PIN), then press and hold
tho buon
The opener light will bink thee times. Release tho
baton
2. Press the temporary ig PIN you have chosen, then
ross Enr.
‘Tho oponer light wil BEnk four imos.

3.10 set the numberof hours this temporary PIN wil work,
press the numberof hours (up 10 255), then press.
or
3.10 sets numberof times this temporary PIN wil work,
press the numberof times (up to 255), then press.
“Tho opener ght wi Bink once when the temporary PIN.
has boon eames
“est by pressing the four buttons forthe temporary PIN,
then press Enter. The door should move. Ihe temporary
PIN was set toa certain numberof openings, remember
{hat the test has used up one opening.To clear the
temporary password, repeat steps 13, seing the number
‘of hours rimes 10 On sep 3

‘One Button Close: Opener can bo closed by pressing any the ENTER bution i the one button close feature has bogn
activated. Tis feature has boen activated atthe factor; To activate or deactivate this feature press and hold butions 1
find 9 for 10 seconds. The Keypad wil Bink twice when the one buton closes acive, The Keypad wil ink our times

when one button close i deactivated

TO ERASE ALL CODES FROM MOTOR UNIT MEMORY

To doactvate any unwanted remote, st rase al codes:
Press and hold the “eam” button on motor ut uti the
loam indicator Eghtgoos out (approximatoy 8 saconds)
Al previous codes are now erased, Reprogram each
remote or keyless entry you wish fuse

THE REMOTE CONTROL BATTERY

>

To replace batten, use the
visor lp or serewariver blade
to pry open the case as
shown nsor battery postive
si up (+),

Dispose of old battery proper.
Replace tho battery with only
32032 coin cel batterie,

À WARNING

To prevent possible SERIOUS INJURY or DEATH

NEVER allow small chen near batteries.
battery sale, immediatly natty dar.

To reduce risk offre, explosion or chemical bum

+ Replace ONLY wit 312092 coin ators.

+ Do NOT recarp, sasembl, eat above 100° (212*F) or
incinerate

E

30. REPAIR PARTS

REY PART

ERE oescmpnon

Sel” à: > A 1 AM Maser mit
RS 7 | |2 roster Compe wotoy assembly
A A 3 13016819 Rad font (header) section
' À (cs Ran, cansan con

5 cas Cn pa

5 sm Chan an cade

7 om iros
nor snow

a Br Se

INSTALLATION PARTS

PART

NO. DESCRIPTION

14104942 _Multtuncion door contol pane!

9500 Singie-buon emote contol

9530 button emote conto!

10820. V2082 Lim battary

2981397 — Transmiterviorcio

412828 Emergency release rope and handle
assembly

41B4494-1 2-conduetor ball wire — white and
winters

41A5047-2 | Heador bracket with levis pin and
fastener

41250471 | Door bracket with cvs pin and
fastener

178835 Curvod door arm section
178834 Straight door arm section
128776 Hangig bracket

41AS094 Salety sonsor kt (ceiving and

sending eyes) wih S(9 m)
conducir bi wir atachod

41452661 Safty sensor brackots (2)
14166 Door Control Button

NOT SHOWN,
A1A5258:11.Insalton hardware bag
11483165 Assemblyinstalation manual

11483169 Installation instructions for one-piece
ors

31. MOTOR UNIT ASSEMBLY PARTS

( FS
EEE
L — Conve um we >,
m DE
Fra BET escasea
DEA een
12 41C4220A Gear and sprocket assembly ‘bracket assembly
‘Complete with: Spring washor, Ihrust ‘Complete with: Motor, worm, bracket,
pie ris Em RU D
aes een eens AS UA cad
PES dr tee
13 4142817. Fr 16 41C4398A RPM sensor assembly
pad 17 41AC0S0-1 Receiver logic board assembly
ls aia Les feat a sete
E netas eos aa as A ee
een co
au ET
innen rei alin ee
E
EE me Ge ee Jara re
en ue Mm. Lia we tors ra)
PE ne cloro
lo 12A373 Capacitor bracket ns PHIADIPOS Lee. DTD,
Io: ‚ann SES nites ne
In zz om A
les ee aoe for sow

4142626 Motor shat bearing kt
4142625 _ Opener assembly hardware kt

a

32. ACCESSORIES

SECURITY" 3-Button Remote
Control

Includes visor ip.

‘SECURITY 3-Button Mini
Remote Control:

ah key ring and fastening sti.

Motion Detecting Control Pane!
Multtuncion door conto with mation
sensor that automaticaly ums opener
lights on for 5 minutes when it detects a
person entering tmmerage. Sensor can
be aasiy deach M unen desea

‘Multi-Function Door Control Panel

Provides a Lock feature which prevents
‘operation of garage door opener trom
Portable remotes and a Light feature for
Constant ight

SECURITY Keyless Entry:
Enables homeowner to operate garage
door oponer rom outside by entering a
password on a specially designed
keyboard. Alo can add a temporary
pasenord for vistors or sendos persons
‘This temporary password can be Im
10 a programmable numberof hours or
ones.

fi

3
8

WA

pi

Outside Quick Relea

Required for a garage with NO
access door.

8 Foot (24 m) Rall Extension Kit:

To allow an 8 foot (2.4 m) door to
Open fly.

10 oot (3m) Rall Extension Kit:
To allow a 10 fot (3 m) door to
pen fly.

Extension Brackets:

(Optional) For safety sensor
instalation onto the wal ar Ro.

To order all 1-900-528-0131

33. NOTES

34. NOTES

35. WARRANTIES

ingens eam Lumen waar

En noron reo wana

‘ozo, one, mk Aso
acer en ete meee ric ion eS pe tn te sty
ERA eq
en
FE EEE AA
eyes al el ou pet mee un «soon ye te cay,
fais ie eat tae SU bt te 2. mus za
er to ae
cad
iS
San
ABOVE EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE MOTOR, WHICH ARE LIMITED IN DURATION TO THE 6 YEARS
ean see eta attrac ee DS re ae
o LS |
(INCLUDING, BUT NOT Li ‘TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE,
de ce si
Bea na D a PNC e op tae on on ve pon
ee en
HOT EERE Sine HE e EIN
SRE D ea ea à
A EE OS
edita
ann
A A on en

‘CHAMBERLAIN 1 YEAR LIMITED WARRANTY
LIFETIME MOTOR LIMITED WARRANTY

PD610D, PD612D, PDS12KLD £ 489300
e Grant Grup ne. (Slur) aran o theft tl ple of ie ra e eee wh hs re can
Tr ya re fen an ml ario! momar a pte oft YEAR hor De o paragon nae MOTOR bee
fom en musta nd marmol De lose te pou Te pope open he posers Spent on jor comen
shire un alan open, amen nd ing Flee cn ey nia Pas ae eae
Wi reg the mt waranty pas, he product oppure to contin a le covered by ie toto waranty, cal
Voodoo aos Sand ts pods Tn nd In prc op anaes tur ses co x wary ear
‘stb nase ar necios sa os a Pose ne a dG a he prion ana ui por ss Neel
Sn pose este mern eps o eel Sater bs mamar) mg ah ue ty Sele am One os
o cie rc aren wtb parece rosal re pn) tr al alma pq Ds
RARE De pate ds Ia par lr sa pin
neo MARRANTY PERIOD ron te WoTOR Ak IMPLIED WARRANTIES Wh EXIST OR APPLY AFTER SUCH PERIOD, Some
MARRANT DOES NOT COVEN NONDEFECT DAMAGE. OMUROE CAUSED DY IMPROPER MSTALLATIOR, OPERATION OR CARE
{mictuoWo, BUT NOT UNITED To ABUSE, MUSE. FAURE TO PROMDE REASONADLE AND NECESSARY MANTENANCE.
FREALACEO UN, REPLACEMENT OF OATTEMIES ANO LH GULOS OR UNTS NSTACLED FOR MORE SEMI USE, DO
TS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH OR RELATE TO, THE GARAGE DOOR OR GARAGE 0097
WWanmantY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENGE ANY Schnee CALL THAT DETEMMNES THE
ounecrion win use, OF ABIT To USE. Ts PRODUCT MNO EVENT SHALL SELLER S UABLITY FOR breach OF
Wannanry each Or CONTRACT NEGUIOENGE OR STMT LABILITY EXCEED THE COST OF THe PRODUCT COVERED HEREBY.
NO PERSON AUmIORIZE To ASSUME FOR US ANY OTHER LAB Y In CONNECTION WITH THE SALE OF ls PRODUCT.
y ou Th Am waranty ges yo sec oes on ou moy stave or tn a kam lo Sao

36. CHAMBERLAIN? SERVICE IS ON CALL

‘OUR LARGE SERVICE ORGANIZATION
SPANS AMERICA
INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE.

SIMPLY DIAL OUR TOLL FREE NUMBER:
1-800-528-9131

www.chamberlain-diy.com

For professional installation, parts and service, contact your local CHAMBERLAIN? dealer. Look fo him inthe
Yellow Pages or call our Service number fora Ist of dealers n your area,

HOW TO ORDER REPAIR PARTS

‘Solin prices wal be fumishe on request, or pats wil be shipped at provaling ricos and you wil be bled
accorsingy.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
PART NUMBER

PART NAME

‘+ MODEL NUMBER

ADDRESS ORDERS TO:
THE CHAMBERLAIN GROUP, INC.
Technical Suppor Group
6050 $. Country Club Road
Tucson, Arizona 88706

SERVICE INFORMATION TOLL FREE NUMBER:
1-800-528-9131

vaste pee?