Corex Process in Iron Making

Corex Process in Iron Making

1. Page | 1



COREX
PROCESS
in
IRONMAKING
Report Submitted by :
Aditya Kumar Singh (5207),
Bachelor in Technology,
Metallurgy & Materials Engineering,
National Institue of Foundry & Forge Technology,
Ranchi, Jharkhand

2. 2
INTRODUCTION:
For decades, there have been number of initiatives towards development of alternative
smelting reduction route of iron making. The reason for such interest stems from the fact that
the conventional blast furnace ironmaking depends on metallurgical coal, which is required
for producing BF grade coke. Continued supply of metallurgical coal at a competitive price is
becoming increasingly difficult with the depletion of coking coal reserves. Besides, the coke
oven batteries are among the most environmentally hazardous reactors so far.
COREX is the first and the only commercially established smelting-reduction process, as an
alternative route to blast furnace, based on non-coking coal. This process, has been
developed and is being marketed by VOEST-ALPINE INDUSTRIENLAGENBAU (VAI),
Austria. The COREX process offers high smelting intensity and hence higher productivity,
ability to use various types of non-coking coals, use of iron ore fines to an extent, low net
operating cost, possible generation of power or other alternative use of export gas generated
from the ironmaking unit, besides being eco-friendly.
Jindal Vijaynagar Steel Limited (JVSL) is an Greenfield venture in Karnataka based on
COREX ironmaking technology, with an investment of over Rs. 6,000 crores. It is supported
by joint ventures, namely, Jindal Praxair Oxygen Company Ltd. (JPOCL), Jindal Thermal
Power Company Ltd. (JTPCL) with co-generation concept and Vijaynagar Minerals Private
Ltd. (VMPL).
The world class performance of COREX plant so far has justified the vision and concept of
such large investment in a cluster of industries co-existing. This conglomerate concept is the
most adaptable in developing countries where there exists significant growing market for
steel, power, cement, industrial gases, mining and mineral processing.

3. 3
ESSENTIAL FEATURES:
COREX consists of two reactors, the reduction shaft and the melter-gasifier. The reduction
shaft is placed above the melter-gasifier and reduced iron bearing material descends by
gravity. The volume of the reduction shaft and the melter-gasifier is about 600 m
3
and 2200
m
3
respectively.

Schematic diagram of a COREX plant

Reduction Shaft:
Iron ore, pellets and additives (limestone and dolomite) are continuously charged into the
reduction shaft via lock hopper system located on the top of the shaft. Some amount of coke
is also added to the shaft to avoid clustering of the burden inside the shaft due to sticking of
ore/pellets and to maintain adequate bed permeability. The reduction gas is injected through
the bustle located about 5 meters above the bottom of the shaft at 850°C and over 3-bar
pressure. The specific reduction gas flow is about 1200Nm
3
/ton of iron bearing burden
charged to the shaft. The gas moves in the counter current direction to the top of the shaft
and exits from the shaft at around 250°C. About 5-6% of coke is also added to the shaft to
avoid clustering of the burden inside the shaft due to sticking of ore/pellets and to maintain
adequate bed permeability. The iron bearing material gets reduced to over 95% metallization
in the shaft and is termed as DRI. Subsequently, six screws discharge the DRI from the
reduction shaft into the melter-gasifier. The metallization degree of the DRI and the
calcination of the additives are strongly dependent on the following parameters:

4. 4
 Amount and quality of the reduction gas flow
 Temperature of the reduction gas
 Reducibility of the iron bearing burden
 Average particle size and the distribution of the solids charged


Process Flow Sheet
Melter-Gasifier:
The melter-gasifier can largely be divided into three reaction zones
 Gaseous free board zone (upper part or dome)
 Char bed (middle part above oxygen tuyeres)
 Hearth zone (lower part below oxygen tuyeres)
Due to continuous gas flow through the char bed, there also exists a fluidized bed in the
transition area between the char bed and the free board zone.
The hot DRI at around 600-800 °C along with partially calcined limestone and dolomite are
continuously fed into the melter-gasifier through DRI down pipes. The DRI down pipes are
uniformly distributed along the circumference near the top of the melter-gasifier so as to
ensure uniform distribution of material over the char bed. Additionally non-coking coal,
quartzite and required quantity of coke are continuously charged by means of lock hopper
system. The operating pressure, in the melter-gasifier is in excess of 3 bars.

5. 5
Oxygen plays a vital role in COREX process for generation of heat and reduction gases. It is
injected through the tuyeres, which gasifies the coal char generates CO. The hot gases
ascend upward through the char bed. The sensible heat of the gases is transferred to the
char bed, which is utilized for melting iron and slag and other metallurgical reactions. The hot
metal and slag are collected in the hearth. The efficiency of the furnace depends largely on
the distribution of this gas in the char bed and utilization of the sensible heat of the gas. The
dome temperature maintained between maintained between 1000°C to 1100°C, which
assures cracking of all the volatile matter releases from the coal. The gas generated inside
the melter-gasifier contains fine dust particles, which are separated in hot gas cyclones. The
dust collected in the cyclones is recycled back to the melter-gasifier through the dust
burners, where the dust is combusted with additional oxygen injected through the burners.
There are four such dust burners located around the circumference of the melter-gasifier
above the char bed. The gas from the melter-gasifier is cooled to the reduction gas
temperature (850°C) through the addition of cooling gas. A major part of this gas is
subsequently fed to the reduction shaft. The excess gas is used to control the plant
pressure. This excess gas and the reduction shaft top gas are mixed prior to the take over
point and is termed as COREX export gas. The export gas has high net calorific value of
approximately 7,500 – 8000 kJ/m³ (STP). This gas is suitable for use for a wide range of
applications like power generation etc.
Typical usage of materials:
Coal use in the C-1000 plant is about 900 kg/thm. The oxygen requirement is 540 Nm
3
/thm.
The production of export gas is around 11.5 GJ/thm. A small amount of electricity is
required, 60 kWh/tonne. On the basis of these data, the Specific energy consumption(SEC)
of the C-1000 plant can be calculated to be 15.5– 17.5 GJ/thm. (All calculations of the
Specific energy consumption (SEC) of smelting reduction processes are summarized in
Table)
Table 1: Materials for the production of 1000 kg hot metal at a COREX plant

6. 6

PROCESS CHEMISTRY:
Corex is a two reactor but three-stage process. The blast furnace concept has been used,
virtually splitting it into two at the cohesive zone interface. Accordingly a Corex plant has
shaft unit, where iron ore pellets (with or without some closely sized lump ore) is reduced by
gases emanating from the second unit to make hot sponge iron (first stage). This is
mechanically transferred to the second unit or Melter-Gasifier where it is melted and
carburised (second stage) by injection of both coal and oxygen. In the upper part of the
Melter-Gasifier a fluidised bed of coal char is maintained (third stage), where any CO2 or
H2O is converted to CO and H2. Since there is practically no CO2 or H2O in the gas leaving
the Melter-Gasifier, we say that the degree of post combustion of Corex gas is zero,
resulting in a gas rich in chemical energy.
Reactions in Reduction Shaft:
Following are the primary reactions taking place inside the reduction shaft:
 Reduction of iron oxide by CO and H2 and transforming the iron oxides to metallic
iron.
Fe2O3 → Fe3O4 → FeO → Fe
 Calcination of Limestone and Dolomite
CaCO3 → CaO+CO2 (endothermic)
CaCO3.MgCO3→CaO.MgO+2CO 2 (endothermic)
 Carbon deposition reaction and formation of Fe3C
2CO → CO2+C (exothermic)
3Fe+2CO → Fe3C+CO2 (exothermic)
Out of the above mentioned reactions, reduction of iron oxide by H2 and calcination
reactions are endothermic. On the other hand, reduction of iron oxide by CO gas and carbon
deposition reactions are exothermic in nature.
The reduction gas is almost fully desulphurized in the shaft due to the presence of the burnt
lime and dolomite according to the following reactions:
CaO + H2S → CaS + H2O
MgO + H2S → MgS + H2O
Low content of hydrogen sulphide of the top gas is important with respect to the further
usage of the COREX gas.

7. 7
Reactions in Melter-Gasifier:
Following are the reactions taking place in melter-gasifier:
 Drying of Coal(100
o
C)
 Devolatilisation of coal (200
o
C to 950
o
C) and liberation of methane and higher
hydrocarbons.
 Decomposition of volatile matter
Due to higher temperature prevailing in the melter-gasifier free board zone, the
hydrocarbons are cracked intohydrogen and elementary carbon
CnHm = nC + (m/2)H2
It is desirable that all higher hydrocarbons are cracked in the free board zone so as to
assure generation of a good quality reduction gas. Maintaining dome temperature between
1000
o
C to 1100
o
C ensures the same.
Other reactions in the free board zone are:
 CO2 + C = 2CO (Boudouard Reaction)
H2O + C = CO + H2 (Water Gas Reaction)
CO + H2O = CO2 + H2 (Shift Reaction)
 Decomposition of the undecomposed limestone and dolomite.
 Residual Reduction of the iron oxide.
 Direct reduction of FeO int the DRI takes place by carbon in the char bed.
 Combustion of coal char by oxygen.
Burning of the coal char takes place near the tuyeres. The maximum temperature
inside the melter-gasifier exists in front of the tuyeres. The following carbon
gasification reactions takes place in the tuyeres area.
2C + O2 = 2CO
2CO + O2 = 2CO2
C + CO2 = 2CO
 Melting and formation of hot metal and slag respectively.

8. 8
A typical analysis of COREX hot metal and slag is give in table 2 & 3.
Table 2: Hot metal analysis


Table 3: Slag analysis


The typical analysis of various gases produced in COREX process is give in table 4.
Table 4: Typical analysis of COREX gases

The efficiency of the COREX process depends on the following parameters:
 Size and chemical analysis of the raw especially the coal
 Low C02 percentage in the reduction gas so as to ensure higher metallization of the
DRI
 Optimum distribution of oxygen between the tuyeres and dust burners
 Permeability of the char bed
 High system pressure
 Higher melting rate operation

9. 9
ADVANTAGES & LIMITATIONS:
Advantages of this process are following –

(i) It substantially reduces specific investment costs compared with conventional
blast furnace steelmaking process; lowers the production costs 15% to 25%
compared with a blast furnace,

(ii) Outstanding overall environmental compatibility, due to reduction in CO2
generated per ton of iron production;

(iii) Use of COREX export gas for a wide range of applications,

(iv) Use of a wide variety of iron ores and coals,

(v) Elimination of coking plants,

(vi) Hot-metal quality suitable for all steel applications.

(vii) Integrated electrical power generation possible.

(viii) Combined production of DRI possible.

(ix) Highest operational flexibility with respect to production capacity, production
stops and raw material changes.

Limitations include:
(i) It has the limitation in distributing the coal and DRI in the optimised manner in
the melter-gasifier. This results in more peripheral flow of hot gases.
(ii) Absence of post combustion means that much chemical energy is lost in the
exit gases and consequently the coal consumption in Corex is much higher
than in any other iron making process.
(iii) The system is maintenance oriented, including cooling gas compressor for
recycling part of COREX gas for cooling the hot gases from the melter-gasifier.
(iv) It is provided with very sophisticated gas cleaning facilities. There are three
gas cleaning streams for cleaning the total gas generated in the process.
(v) Hot DRI transfer and hot sas recycling are hazardous especially during their
maintenance periods.
(vi) The melter-gasifier is subjected to high occurrence of pressure peaks on
account of use of raw coal with poor char bed conditions. This results in
jamming of dust recycling systems as well as gas cleaning systems thereby
resulting in more downtime of the plant.

10. 10
(vii) The process is sensitive to the quality of inputs particularly with respect to
quality and granulometry, the input of fines, decrepitation, and degradation
behaviour of coal, iron ore and pellets at high temperature. Inferior quality of
inputs result in frequent jamming of screws, DRI downpipes and DRS lines,
affecting furnace availability.

11. 11
WORLD SCENARIO:
 Development of the COREX process dates back to the 1980s and was performed by
Voest-Alpine (Germany/Austria). The first commercial COREX unit was constructed
between 1985 and 1987 at ISCOR’s Pretoria works, after first testing the process in
Germany. The plant had various problems (due to inexperience) after the start-up in
December 1987. After reconstruction and de-bugging, the plant has been
successfully in operation since 1989 and was given over to ISCOR(capacity 300,000-
ktpa). Reconstruction of some parts and new operation conditions improved the
performance greatly, leading to production of high quality iron, and high productivity
and availability. The plant demonstrated to be economically attractive, with 30%
lower production costs than the blast furnace on site, despite the low capacity of
the COREX unit. The clean excess fuel gas is used on site in furnaces and coke
ovens. The COREX process proved to be very flexible(with respect to the fuel rate,
and additives addition), insensitive to high alkali content of the ore (and burden), and
easy to operate.

 The preliminary success of the first COREX plant lead to the decision to build a
larger COREX (C-2000, 650,000 tonnes per year) in South Africa by Saldanha Steel,
a subsidiary of ISCOR. Saldanha Steel is now a part of Mittal Steel South
Africa which in turn is part of global steel company Arcelor-Mittal. In 1998, ISCOR
decided to close the Corex-based Pretoria plant due to an “unprofitable economic
situation”. The off-gases of the new COREX unit will be used to produce 800,000
tonnes per year of DRI, following a similar design to that at HANBO Steel, South
Korea. This decision also seems to be based on the environmental performance of
the COREX process, as the site is located near a nature preserve. This plant, which
includes a thin slab caster, began operation in January 1999.

 Since 1995 a COREX plant has been in operation in the Republic of Korea, with
twice the capacity of the South African plant (C-2000). South Korea’s Pohang Iron
and Steel Co. has a 600,000-700,000 ton per year unit COREX plant. Several more
orders have been placed for C-2000 plants in India, South Korea, and South Africa.
 The Chinese steel producer Baosteel Pudong Iron and Steel Co. Ltd. (For Short
Pudong steel) at Luojing, near Shanghai started up a Corex C-3000 plant in early
November 2007, with a nominal production capacity of 1.5 million tons of hot metal
per year. The project was completed under the management of Siemens Metals
Technologies within a period of 29 months.
 The latest generation of Corex plants, the C-3000, is ideally suited for integration into
green- or brown-field steel works projects. It can replace the blast furnace, or can be
used as a source of virgin iron for minimills. The economics of the Corex plant
already provide an answer to future scrap and coke shortages, and the continually
increasing demands placed on steel quality. Another alternative is the installation of a
Corex C-3000 plant as a stand-alone merchant plant for the production of hot metal
and/or pig iron.

12. 12
 In the United States, Geneva Steel has joined Air Products and Centerior Energy in a
Department of Energy project to demonstrate the commercial viability of the Corex
process in the United States.

World's Largest Corex Ironmaking Plant setup by the Chinese steel producer
Baosteel Pudong Iron and Steel Co. Ltd.

13. 13
INDIAN SCENARIO:
The COREX C-2000 Plant/Module 01 at Jindal Vijaynagar Steel Ltd., Tornagallu, Karnataka,
India, Successfully started on August 8, 1999. Jindal Vijaynagar Steel Limited (JVSL) project
is located in the midst of the rich iron ore belt of Bellary- Hospet in Karnataka.The JVSL
project is conceived as the one of the most modern, technologically efficient Greenfield plant
with a capacity of 1.6 mt per annum.
As a highlight of this proven technology, more than 75% of the nominal capacity was
reached shortly after start-up. The excellent hot metal quality fulfils the requirements of the
LD(BOF) shop. The plant was installed by VOEST-ALPINE INDUSTRIENLAGENBAU (VAI),
a company of the listed VA Technologic AG. This was the forth plant which was put in
operation for the production of hot metal based on VAI’s proprietary COREX technology. It is
planned that the COREX export gas will be used for electrical power generation and for
heating purposes within the steel complex. Hot metal from the COREX plant is processed to
high quality steel in two 130 t LD(BOF) converters. The slag produced by the COREX plant
is processed in the granulation plant and will be sold to cement industry.
The steel making facility (BOF-CCP shop) include two 120 T convertors and two single
casters of latest design and state of art facility from Mannesmann Demag of Germany. The
quality slab produced will be suitable for hot strip mill which has been engineered by Daniel
United of USA, incorporating the latest technology of coil box and a 250 T walking beam
furnace from Stein Heurty. A third generation mill is equipped with state of art electrical
automation from Cegelac, USA and has all modern control features and equipment, to
produce internationally competitive quality strips of 1.6mm to 12mm thickness up to a width
1250 mm.The JVSL project is visualised on co-generation concept and the unique feature of
the project is its technology-cum-management model. Jindal Praxair Oxygen Company
Limited, the joint venture company, supplies oxygen to the COREX plant. COREX off-gases
will be used to produce power by another joint venture company, Jindal Tractebel Power
Company Limited.
An overview of JVSL COREX Plant
Rated capacity : 1.6 million tpa
No. of units : 2 Module C-2000
Major units : Coal Blending Station
Coal Drying Plant
Stock House
COREX Tower
Cast House
Water recirculation System
Gas Cleaning and Distribution System
Slag Granulation Plant
Salient Technical features : Use of non-coking coal.
Availability of COREX gas of medium calorific value for
use as fuel in the steel plant as well as Power Plant.
Environment friendly process.

14. 14
Table 5: gives the comparison of JSVL, Posco and Saldanha
Plant
JVSL
POSCO SALDANAH
Corex-1 Corex-2 Total
Production,
tonnes
797969 826475 1624444 626931 707002
Annualised
Melting rate,
t/hr
91.09 94.35 92.72 71.57 80.71
Fuel Rate,
Kg/thm
1004 1005 1005 1154 1122


Table 6: shows the progress of COREX performance in JVSL
Year Production, mt
Sp.Fuel
consumption,
kg/thm
Hot metal
Temp., C
`Si', % `S', %
1999-2000 0.40 1163 1491 0.75 0.060
2000-2001 0.77 1071 1503 0.66 0.037
2001-2002 1.52 1082 1497 0.58 0.037
2002-2003 1.46 1041 1497 0.71 0.029
2004-2003
(Till Jan' 04)
1.36 1000 1487 0.76 0.027

15. 15

Jindal COREX Plant at Vijaynagar

16. 16
REFERENCES:
 “Smelting Reduction for Iron Making”
by A. K. Jouhari, 2002 (Pages 44-58)
 “Future technologies For energy-efficient Iron and steel making “
by De beer, Worrell & Blok , 1998
 http://www.industry.siemens.com/metals-mining/en/Ironmaking/corex.htm
 http://jpcindiansteel.nic.in/corex.asp
 Article by M. Gojic and S. Kozuh, Faculty of Metallurgy, University of Zagreb, on
“Development of Direct Reduction Processes and Smelting Reduction Processes for
the Steel Production”
 Report by Lynn Price, Dian Phylipsen, Ernst Worrell on “Energy Use and Carbon
Dioxide Emissions in the Steel Sector in Key Developing Countries”