EPAS 10- LESSON 7 ELECTRONIC TOOLS .pptx

ELECTRONIC TOOLS AND MATERIALS

1. Electronic Tools and Materials

2. In every electronic work, it is a must to prepare first the necessary tools, materials, and equipment needed as well as the information. The following list of tools, materials, and equipment are needed in maintaining and repairing.

3. Soldering Iron with stand A soldering iron is a hand tool used in soldering. It supplies heat to melt solder so that it can flow into the joint between two workpieces. A soldering iron is composed of a heated metal tip (the bit) and an insulated handle.

4. Soldering Lead  is a metal alloy usually made of tin and lead which is melted using a Soldering iron.

5. Desoldering Tool     A desoldering pump, or a solder sucker, is a tool that sucks up the molten solder through a vacuum. You can use this tool to easily remove the solder, especially in PCB boards.

6. Diagonal Cutting Pliers     are pliers intended for the cutting of wire (they are generally not used to grab or turn anything).

7. Long Nose Pliers    long-nose pliers, also known as needle-nose pliers and snipe-nose pliers, are both cutting and holding pliers used by artisans, jewelry designers, electricians, network engineers and other tradesmen to bend, re-position and snip wire.

8. Wire Stripper     A wire stripper is designed to remove the outer jacket, or insulation, of a wire

9.     to maintain a firm and safe grip while turning and holding nuts and bolts. Adjustable Plier

10.    this has a cross tip resembling a positive (+) sign. This is used to turn screws with cross slot heads. Philip Screwdriver

11.    The blade is wedge –shaped and resembles a negative (-) sign. This is used to drive screws with a single slot head. Flathead Screwdriver

12.  have a closed loop on one side (box-end) for hexagonal or square nuts, while the other end is an open U-shape (open-end). These wrenches are often used for nuts that are hard to loosen. The closed-end can loosen the nut, while the open end is then used to unscrew it fully. Combination Wrench

13.  is any type of knife used for general manual work purposes. Such knives were originally fixed-blade knives with durable cutting edges suitable for rough work Utility Knife

14.  A multimeter (also known as a volt-ohm-milliammeter, volt-ohmmeter or VOM) is a measuring instrument that can measure multiple electrical properties. A typical multimeter can measure voltage, resistance, and current, in which case can be used as a voltmeter, ammeter, and ohmmeter. Multitester / Volt- OhmMilliammeter (VOM)

15. Antistatic wrist straps  are designed to prevent build-up of static electricity and safely ground operators who are working with ESD sensitive components ESD Wrist Strap

16. Surgical masks help protect your nose and mouth from splattered of body fluids, respirators filter the air before you inhale it. Goggles help protect only your eyes from splatters. Mask

17. This brush can remove dirt, webbings, and many more unwanted entities on your projects without a hitch. It has a curved handle for better handling and firm bristles that will surely leave your PCB shining bright.  Non-Static Brush

18. a protective or decorative garment worn over the front of one's clothes and tied at the back. Apron

19. The use of cable ties is common in automotive electrical applications for bundling and securing wiring, cable, wire harness conductors, hoses, and more. Cable Tie

20. Electrical tape is a pressure-sensitive tape used to insulate materials that conduct electricity, specifically electrical wires. It stops the electrical current from accidentally passing to other wires, which could create a short or even start an electrical fire. Electrical Tape

21. Goggles are the primary protectors intended to shield the eyes against liquid or chemical splash, irritating mists, vapors, and fumes. They form a protective seal around the eyes, and prevent objects or liquids from entering under or around the goggles. Eye Protector/ Goggles

22. A  glove  is a garment covering the hand, with separate sheaths or openings for each finger including the thumb.  Gloves

23. Solder paste is used in the manufacture of printed circuit boards to connect surface mount components to pads on the board. Soldering Paste