Military standard 105E and 414

Military Standard 105 E and 414 with solved numerical. SQC

1. MILITARY STANDARDS
4.09.2015

2. 4.09.2015 2
Military Standard 105E
Most widely used acceptance sampling system for attributes
MIL STD 105E is Acceptance Sampling System
collection of sampling schemes
Can be used with single, double or multiple sampling plans
We will consider single sampling plans for this course

3. 4.09.2015 3
Inspection Types
Normal Inspection
Used at start of inspection activity
Tightened Inspection
Instituted when vendor’s recent quality history has deteriorated
Acceptance requirements for lots are more stringent
Reduced Inspection
Instituted when vendor’s recent quality history has been exceptionally
good
Sample size is usually smaller than under normal inspection

4. 04.09.2015 4
Switching Rules
- Production Steady
- 10 consecutive lots accepted
- Approved by responsible
authority
NormalReduced Tightened
- Lot rejected
- Irregular production
- Lot meets neither accept
nor reject criteria
- Other conditions warrant
return to normal inspection
2 out of 5 consecutive lots
rejected
5 consecutive
lots accepted
10 consecutive lots remain
on tightened inspection
Start
Discontinue
Inspection
AND conditions
OR conditions

5. Procedure for MIL STD 105E
Choose AQL
Choose the inspection level
Determine the lot size
Find the appropriate sample code size letter from table A-1.
Determine the appropriate type of sampling plan to use.
Enter appropriate table to find the type of plan to be used.
Determine the corresponding normal and reduced inspection
plans to be used when required.
04.09.2015 5

6. 04/09/2015 6
Example
Suppose product comes from vendor in lots of size 2000
units. The acceptable quality level is 0.65%. Determine the
MIL STD 105E acceptance-sampling system.

7. 04/09/2015 7
Normal Insp. Level
Lot Size
= 2000

8. 04/09/2015 8
AQL
Plan K
Sample 125 units.
Ac = 2, accept if defects ≤ 2.
Re = 3, reject entire lot if defects ≥ 3.

9. 04/09/2015 9
AQL
Plan K
Sample 125 units
Ac = 1, accept if defects ≤ 1.
Re = 2, reject entire lot if defects ≥ 2.

10. 04/09/2015 10
Sample 50 units
Ac = 1, accept if defects ≤ 1.
Re = 3, reject entire lot if defects ≥ 3.
AQL
Plan K

11. Military Standard 414
MIL STD 414 is a lot-by-lot acceptance-sampling
plan for variables introduced in 1957.
Sample sizes are a function of the lot size and
the inspection level.
All sampling plans assume the quality
characteristic of interest is normally distributed.
04/09/2015 11

12. Military Standard 414
MIL STD 414 is divided into four sections:
A: general description of the sampling plans including
definitions, sample size code letters, and OC curves
for the plans.
B: variables sampling plans based on the sample
standard deviation for the case in which the process or
lot variability is unknown.
C: variables sampling plans based on the sample
range method
D: variables sampling plans for the case where the
process standard deviation is known.
04/09/2015 12

13. 09/07/15 13

14. Procedure 1 (k-Method)
04/09/2015 14

15. Procedure 2 (M-Method)
04/09/2015 15

16. Double specification limit variability
unknown
04/09/2015 16

17. Example
04/09/2015 17

18. Range method for variability
unknown
If mentioned in the question then we will go for
this method.
In this method all the steps are same as we have
done before only difference is instead of
calculating standard deviation we will calculate
range.
The table used in this method is C1 or C2 and C3
or C4.
04/09/2015 18

19. Thank You
09/07/15 19